Jump to content
SAU Community

How To Take Off Factory Steering Wheel

Sammie

By Sammie,
in Exterior & Interior Styling

 Share

Recommended Posts

Sammie Proficient

Sammie

Posted
Posted

im trying to take off the factory steering wheel in my s1 33 gtst ive taken off the main bolt what do i have to do next ive tried pulling on it and wiggling it a bit but no luck and this is the first time for me any help would be great trying to do it right now

Medium Dave Proficient

Medium Dave

Posted
Posted

MacGuyver is right, track down one of these steering wheel puller's, I think it is possible to do damage to the collapsable steering colums if you dont -Disclamer on that last statement: not completely sure, something someone told me once years ago, could be wrong, i dunno, but why take the risk?

MacGuyver Mentor

MacGuyver

Posted
Posted

Yeah I've heard of damaging the collapsable steering columns as well. You should be able to get a steering wheel puller from somewhere like Repco or Super Cheaps, doesn't cost much. Don't try to remove it with out one! And make sure that when you do remove it, the front wheels are straight so when you put the new wheel/old wheel back everything is straight again.

"My cat's name is Mittens."

blind_elk Grand Master

blind_elk

Posted
Posted

You can usually get them loose by grabbing the wheel at "quarter to three" and wiggling back and forth (along the axis of the steering column, not like you are turning a corner) at the same time as pulling the wheel towards you.

It is probably a good idea to leave the nut on a few threads to avoid belting yourself in the forehead when it finally gives.

Rednisr31 Community Regular

Rednisr31

Posted
Posted
You can usually get them loose by grabbing the wheel at "quarter to three" and wiggling back and forth (along the axis of the steering column, not like you are turning a corner) at the same time as pulling the wheel towards you.

It is probably a good idea to leave the nut on a few threads to avoid belting yourself in the forehead when it finally gives.

i have an r31

i took a stock wheel off on wednesday

i used a hammer and left the bolt on as you would want to instead of copping a steering wheel to the face

Lazy-Bastard Grand Master

Lazy-Bastard

Posted
Posted

Steering wheel puller

Either side of the centre nut that holds the wheel on there will be 2 threaded holes (one either side).

The puller kits come a main piece shaped like so =0=, There will be a large bolt that goes through the centre of the puller and butts up to the bolt that holds the steering wheel on. Also in the kit will be a range of bolts to fit different thread sizes for the 2 threaded holes on the sides that I mentioned before.

Just screw the two side bolts in so there is a decent amount of thread holding them in and then screw the large centre bolt in until the wheel pops off.....5 minute job.

sidewazegtst Collaborator

sidewazegtst

Posted
Posted

Hey man what's up.

If your planning on using an aftermarket wheel and hub, let me know how it all went together please. Mainly how easy it was to make the horn work b/c I'll be doing the same thing on my car soon.

Thanks a lot.

Cheers B)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...