Jump to content
SAU Community

Gearbox Oil Leaking Out Of Shifter. Whats The Go?

Civicboy
 Share

Recommended Posts

Civicboy Explorer

Civicboy

Posted
Posted

Hey once again guys,

Changed my clutch on the 32 this weekend. Everything went sweet as until I drove hard for a lil bit and at high revs I noticed some gearbox coming out of the bottom of the shifter. (I left the rubber and console surround off just to get a look while driving).

Maybe I trucked up a seal when putting back the shifter?

Maybe this is normal and the boot catches all the oil and it drains back down eventually?

Its got me baffled!

I need a solution

Thanks dudes

TokyoTaxi Veteran

TokyoTaxi

Posted
Posted

Once the shifter is back in, put the boot back in place and then put a cable-tie around both the large and small ends of the boot. Zip em up as tight as you can and all should be apples !

FurryBarry Enthusiast

FurryBarry

Posted
Posted

Are we talking about an rb20 or 26 here? 'cause the 26 shifter has an inner and outer boot. Maybe you fingered the inner one? I think both the inner and outer boots are the same as in a VL commonwhore, so they should be cheap as dirt if you need to replace them.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      George's R33 GTST build

      By The Bogan · Posted

      I would paint match the whole thing to avoid unwanted attention  I had a similar bonnet, paint matched, on my old R33 GTST, but mine was a fibreglass jobbie made by Blitz in QLD, they work extremely well for radiator efficiency and under bonnet temps
    • shortyboy
      Drive By Wire Conversion options

      By shortyboy · Posted

      Does anyone run this kit with factory plenum? Does the adapter and bosch tb fit under factory strut brace? I wanted to get this setup before going forward facing manifold. Thanks
    • pogman
      George's R33 GTST build

      By pogman · Posted

      small update time, after always wanting a "cool" looking bonnet for my car and always struggling to find one for the series 2 that i liked and wasn't an insane amount of money. Saw one i liked on RHDjapan from D-speed in Japan the price was very good for a carbon bonnet so good infact i was a little unsure how much i trusted it, decided to bite the bullet and with the help of jesse streeter in not long at all it was at my door. Once it was delivered i ran in from work and quickly unboxed it and to my surprise the quality was actually pretty good i quickly removed the old bonnet and placed on the new one to test it out and even the fitment wasnt too bad at all. Then decided to paint the little grille in the bonnet black to stop it sticking out so much.   I decided to not mess around with the hood latch and just install some aero catch hood pins, having never installed them before did some YouTube university classes and i was good to go. fair to say it is not a fun job at all from making brackets so the pins sit nicely and actually cutting through the bonnet but also being very scared of cutting the holes too big it took wayyyy longer than i would like to admit but finally got it there. Then it was time for a quick test drive to ensure the latches actually worked and thankfully the bonnet looked very stable. I still think paint matching the bonnet and leaving just the part that sticks up as carbon would help make it all look alot neater as im not sure how i feel about all that carbon on a very fridge white car but will leave it as is and see how i feel with time.  
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      I think it's bound to happen, you finally get it all perfect, and bam, something will happen. I took a while to get a Commodore rear quarter repaired where a P Plater clipped it. Two days after getting it back, Sarah wiped it out on a concrete pillar in an underground car park... This is why I take forever to repair them, it stretches how long until it gets bent again... 😛
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Nah, not really responsible for that little fiasco, but I'm still pissed at myself for writing off my 86, or when I reversed my VX into a pole just before selling it, but, meh, 5hit happens to stuff, all it takes is a slight distraction, and life is full of distractions, and "dooh" moments   
×
×
  • Create New...