Jump to content
SAU Community

1995 Silver R33 Skyline Gts-t S1.5

fooey

By fooey,
in For Sale (Private Whole cars only)

 Share

Recommended Posts

  • 2 weeks later...
fooey Collaborator

fooey

Posted
  • Author
Posted (edited)

Willing to negotiate, but not that low.

It's not a S1 its a S1.5 :P It's a special model that Nissan released prior to the Series 2 (as you can see its got several S2 components, high wing, driver's airbag, S2 AFM, and probably other things I've forgotten as standard eq).

Plus this model is clean, has the rare factory sunroof, and is a good base for those to mod or also for those who want a stock car.

Edited by fooey
sindows Veteran

sindows

Posted
Posted

But it has extremely hight kms. I am just giving some advice... I picked up my S1.5 with some minor mods and 76k original logged kms for $12.5k

fooey Collaborator

fooey

Posted
  • Author
Posted

OK thanks mate.

You got yourself a very good deal! Must have been a fire sale as that is the price of a 32 gts-t. Even the 33 nonturbos/autos cost more than that.

I wouldn't say my car has high KMs for a 1995 car...that is actually considered low KMs, but I'd be a bit pessimistic about a car the same age that had significantly lower KMs.

I'm in no rush, and I'm after a buyer who has an eye for detail and wants something clean, either as a base for their next project car, or someone who wants to run it just as it is.

  • 1 month later...
Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

sindows,

your clock was probably wound back or the dash was changed to one with lower km's

5/10 skylines have their dash wound back... a car that is 10 yrs old and less than 10000km / year? thats hard to believe...

sindows Veteran

sindows

Posted
Posted
sindows,

your clock was probably wound back or the dash was changed to one with lower km's

5/10 skylines have their dash wound back... a car that is 10 yrs old and less than 10000km / year? thats hard to believe...

Not when you have log books matey...

fooey Collaborator

fooey

Posted
  • Author
Posted

Thanks for the comments guys.

I'm still running the stock boost solenoid.

1) You either take the dyno sheet with a grain of salt (as all dynos are different) though I can provide the sheet.

2) the boost guage is second hand, so may be reading incorrectly, but it does run to 10PSI max.

3) I have one of those super performing cars :D

  • 2 weeks later...
Freddy Kruger Mentor

Freddy Kruger

Posted
Posted (edited)

South East suburbs of where? has it had the 100000km service where they replace the timing chain n all that shizzle?

actually dont worry bout that. i DLed the doc and see its had the major service.

If your in Vic and this is still for sale in ma month or so you may get an email from me ;)

Edited by Freddy Kruger
  • 2 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Potential MAP Reference Point

      By joshuaho96 · Posted

      Isn't there a fitting on the back of the balance tube? That's what the OEM boost gauge uses.
    • GTSBoy
      Potential MAP Reference Point

      By GTSBoy · Posted

      Getting a decent signal from all 6 throats is a challenge. I don't know for sure, but I suspect that the stock balance tube is not ideal for it. I have done it on an ALFA 4 cylinder (about 35 years ago, so don't ask for too many details). We drilled 4x holes in the manifold runners, put in some fittings and ran hoses to a decent sized (I think it was about 20mm diameter) pipe that ran the length of the inlet manifold. So, it was quite a decent volume. There is a "tuning" balance to be found between the volume of the common plenum on such a thing and the diameter of the pipes running from it to the runners. You need the volume to be large enough to damp out the sharp spikes in pressure signal you get as each runner gets sucked on by its cylinder, but not so large that it becomes too slow to respond to actual changes in MAP. And you need the hoses to be small enough to transmit the signal quickly, but not so small that they delay the signal. You might have to have more than one go at it, if there isn't any actual success based wisdom to be had here. Hopefully there is. Anyway, I would not do it on only a couple of cylinders. I would also not care about "permanently modifying a part". Just bloody drill holes and make stuff better. There is nothing sacred about any GTR unless it is a genuine museum piece that you shouldn't be modifying at all anyway.
    • MBS206
      NC MX5

      By MBS206 · Posted

      He's still joining you, he's just delayed it and won't have the fulleh sick ITBs...
    • Kinkstaah
      R34 GTT front hood lip

      By Kinkstaah · Posted

      The strange thing is this is a URAS front bumper (or clone of it). The bumper actually does not sit flush with the GTT hood - You need the addon to make the hood 'long' enough to reach the bumper. I have no idea why they didn't incorporate this piece into the bumper itself.. instead of sticking it to the hood instead.
    • AdiR34
      R34 GTT front hood lip

      By AdiR34 · Posted

      Another thought on this OLD topic: When you paint your bonnet lip, leave a small unpainted back lip/line along the back of the lip, where it rests on the bumper. That way, the line in the back is much more prominent than the gaps in the front/under the lip - and it breaks the hood-to-bumper connection at the "correct" place, when comparing to a GTR. I'm gonna do this with mine this week, so stay tuned for pics!
×
×
  • Create New...