Jump to content
SAU Community

Problem With Hicas On R32 Gtst

Hui
 Share

Recommended Posts

Hui Enthusiast

Hui

Posted
Posted

Hi all,

I was driving today and all of a sudden the hicas light came on, nothing happened at first then after a while the steering got heavy and would jerk when i turned. the other weird thing is that there's a tapping noise coming from under my feet which i can hear and feel when i turn the steering. I am at a loss as to what the problem could be i ran a search but didnt turn up anything useful any help would be much appreciated

Link to comment
Share on other sites
[200] Mentor

[200]

Posted
Posted

Hui,

Usually when my light came on it was caused by low fluid level in the steering resevior, check that. as for the knocking noise, perhaps a steering shaft universal is starting to fail of is hitting something, check also the steering shaft rubber dampner

Link to comment
Share on other sites
Hui Enthusiast

Hui

Posted
  • Author
Posted
Hui,

Usually when my light came on it was caused by low fluid level in the steering resevior, check that. as for the knocking noise, perhaps a steering shaft universal is starting to fail of is hitting something, check also the steering shaft rubber dampner

i'll check them out 200 thanks

Link to comment
Share on other sites
Hui Enthusiast

Hui

Posted
  • Author
Posted

i got another problem i think theyre related my battery died this morning and alarm was goin off. chargeed it took it for a drive, the steering is still twitching and hicas light flashes on and off. need help please, has anyone had this happen to their cars before?

Link to comment
Share on other sites
Hui Enthusiast

Hui

Posted
  • Author
Posted
Have you reset the ecu?

Just a thought, could't harm anything if it is a fault in the programming or something

Yeah mate tried that and ran diagnostics no faults came up but i still got the same problem. i charge my car up drive it hicas light comes and steering wheel tugs when i turn, leave it over night battery dies again when i go to start it in the morning and this batterys brand new, its freking me out

Link to comment
Share on other sites
sidewazegtst Collaborator

sidewazegtst

Posted
Posted

You can try checking that your altenator is charging the battery properly and if it is, then you've got a draw. Meaning despite the car being off there's still power going to something and causing a drained battery come morning. Worth a check anyway.

As for the HICAS prob, maybe be a sensor problem that only acts up periodically and was fine when tested it, most likely (knowing your luck) it worked fine then and then crapped out later on you. These things are hard to trouble shoot so the next time the light comes on, do the test then. Hopefully you'll get an answer.

Good luck.

Cheers B)

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Thanks Santa (the neverending trials of the 400,000klm, 400kw, RB30, manual swapped Stagea)

      By Duncan · Posted

      Hey Matt, Link pointed to the 2x IGN power sources from the car as a likely issue, and sure enough pin 31 in the loom does not have power when IGN is on (24 does). So at the ECU, (and this is probably the case for R32 as well as C34) most of the ECU loom goes through the firewall behind the blower motor and there are 2 plugs (of 3 in the junction box) which go up and under the dash, the third plug heads under the carpet to places unknown (likely a body to dash loom joint) So, I started to follow that problem through yesterday. Like Johnny (and R32) I assumed that power was supplied through the 2 connectors near the left headlight so I spent some time pulling the intake etc off and cleaning of 400,000klm of dirt and oil leaks and checking those pins, but there was nothing related to the engine parts or ignition fuses there (and no purple with white trace wire in either side of the connectors) Given that the wire didn't seem to go via the engine bay, I then checked there is continuity from Pin 31 to the second connector to confirm no wiring issue in the ECU loom (it looked likely, given how much that has been hacked up over the years!). The pin marked with the purple dot is the other end of the wire to Pin 31 Then I check for IGN power in the dash loom side of that connector with the key on. Nothing. Given that loom goes up and underneath the top of the dash there is no tracing it without taking the dash out, so I went to the driver's side to see if I can find the other end of that (I'm expecting to get to big body junction boxes after I pull enough apart). However, to get to those functions, I had to pull the covers off the drivers side, I'm pretty sure the problem is in this pic Yep, factory remote start (bottom right), local immobiliser (middle) surrounded by 20 years of butchery. Plan is to totally remove the remote start and immobiliser (I think I will lose remote central locking temporarily as a result) to remove all the suspect stuff given I have other more modern security in the car It's gonna take a while, and it is both cold and uncomfortable out in the shed, not looking forward to it.
    • BASHERnissan
      R32 clutch master cylinder

      By BASHERnissan · Posted

      Hey team,  The clutch on my newly bought 25 swapped r32 feels average and sticks half way. Went to go order a new clutch master but it does not look like the ones that suit the one that’s in the car…    does anyone know what clutch master is this just by looking ?  (The feed is on the side rather than the bottom like the ones the pop up online)  thanks guys new to the RB scene so any help is appreciated cheers !!
    • MBS206
      Synthetic oil versus conventional oil

      By MBS206 · Posted

      Id be more than happy to sign up!!! Where do I send the invoices for my fuel usage? I'm happy to provide the mower, oil, and the labour to abuse the motor, just a little help on fuel would be great...   I had tipped the container of oil out into my big "drip tray" and left the small container upside down to drain the oil out of itself overnight. PIcked the container up today, and it has a layer of what feels like either dirt, or shit tonnes of carbon in the bottom of the container. I'm leaning towards it likely being dust, as I doubt the quality of the Sunli BumbleBee having a decent air filter on it, and sections of my yard produce a dust storm, especially because of the high lift blade!   So, filled her up with some fresh Nulon. Seemed to run fine, but it seems to want to run at really high RPM (higher than normal) even with the governor spring slacked off after fire up to try reduce it. If I back the throttle off it a bit to drop the rpm to where I'd like it to be when mowing light grass, it starts to blow a bit of smoke out the exhaust. Opening the throttle back up clears that out. It's definitely breathing oil, as I put my hand down at the breather hose and it's spitting some oil.   My guess is it having been running at high rpm, oil never changed, and it eating dust has destroyed the rings. You know what that means? Time to send it!!!
    • Kinkstaah
      Feedback on Carbonetics: R34 GTT cooling panel

      By Kinkstaah · Posted

      That is what will seal with the bonnet closed. Follow it down while closing the bonnet to see where it ends up with the bonnet closed. The panels don't do anything other than spending money, which this one will do just fine. :p
    • PranK
      Synthetic oil versus conventional oil

      By PranK · Posted

      Nah just send me a photo or a drawing and I'll tell you which is better.  It's a new SAU service.
×
×
  • Create New...