Jump to content
SAU Community

Recommended Posts

I have a standard R32 basically just a air intake, fuel pump and manual boost controller. I'm running it at 12 psi but it seems to drop boost from 12 pretty quickly at higher revs. I was told a digital boost controller would make a pretty big difference. Any thoughts out there?

the pressure will vary and taper off most likely due to an exhaust restriction. you should get a 3" turbo back exhaust system, this will free up the backpressure and also give you some more power everywhere as it will allow the engine to breathe easier. a digital boost controller will also help the boost taper off a little, but it will only try so much, if the physical exhaust system doesn't allow then it simply wont allow it

dude got the same prob with my 32 running same boost, my mechanic told me its the stock 32 turbo, and when i put something bigger on it will hold boost till redline better, i have a full 3" zorst from the turbo back..

i have a ebc that holds boost at 3800 and 4800 fine, but once u go over 5 or 55 as u accelerate up the boost fades off say from like 13 to 11.5 or so

so relax dude from what im told that shiz is normal.

but hey my mechanic could be a blowass and we might both have a problem :P

im waiting till i put my new turbo on and see what happens.

If you do what Paulr33 suggested you should get boost to hold untill round 6-6.5k but after you will get a fair drop in boost.

The stock RB20 Turbo tends to run out of puff after that.

Edited by RedDrifter

its always goin to happen with a manual boost controller it is just 1 of the cons of hvin 1 an electronic boost controller will help cause they adjust themself to keep boost constant but it would also be ur turbo the rb20 turbos r pretty small i am just about to upgrade mine to an rb25 hi flow

Thanks for all your help guys that is much appreciated. I will get the 3 inch and thats the only real way to find out. I do plan on getting the R33 turbo on shortly. Gor about $600 you can't go wrong.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, more pain. The FAST manifold is a little larger than the stocker. This is problematic because there really wasn't much clearance to begin with, so going from 'barely enough' well into 'no' is sad based on the external dimensions of the thing, even though where it bolts to the head is the same. Result is the fuel rails sit a good 25mm higher, and this is a bit of an issue with the wiring that runs behind the motor, and the fuel lines, and everything else. When pushing the manifold on, it required a huge amount of force to crush wiring looms to fit it, sensors like the MAP sensor are about 1mm from the firewall, and the FPR just has to bend ABS lines to be forced into place. After some brainstorming and some sad drinking, the loom for some reason ran from the grommet behind the ABS sensor, then to the driver side head, then back to the passenger side head. So all of this was pulled back and stripped, a few wires cut and rejoined, so that the 'branch' was now on the passenger side's head as below: Before you basically couldn't see anything behind the driver head. This is much improved! The MAP sensor is now pointing up (instead of at the firewall) Brackets have been made up for the rail. The rails are for a LS1, the manifold is designed around a LS2 as it's base. Which of course has slightly different bracketry and water pump clearance, hence the mods people need to do. Should be hopefully mounted tonight. I spent money on a new FPR that is slightly more compact than my Turbosmart FPR1200. The gauge has also been moved to the rail. There's also apparently an ORB to AN Union instead of the adapter, because the ~25mm of the current adapter is going to make the difference. Provided this all goes together and arrives today, it'll be the totally not stressful attempt to start it.
    • This seems like a pointless exercise. There is no E30 availability. Ongoing availability of E85 should not be assumed. Flex-fuel is the only sensible approach, so you can use E85 when and where you can get it, 98 when that's al you can get, and anything in between as you fill it up and drain it down. And if that means replacing the pumps, fitting a flex capable sensor/ECU/whatever has to be done to these Renault shitboxen, then.....so be it?
    • Sorry, I wasn't very clear.....just that the standard injectors are apparently good over 600rwhp/450rwkw which you won't get to on standard turbos anyway.....they are much better sized from factory than we are used to in RBs.
    • I'm not sure where you are, but United Terrey Hills has E85. 
×
×
  • Create New...