Jump to content
SAU Community

Recommended Posts

just had my car tuned made 265rwkw on 17psi. On the dyno using the lap top software the car registered no pinging (30-40 on full load). Now we took it for a drive on the road and its making 140 knock on the hand controller.. im puzzled!

The tuner and my mechanic listened carefully but heard no pinging. but at 140 knock on the hand controller would definately be heard when driving or near the motor. So my question is is my knock senser dodgy? or is it too sensitive and just picking up engine noise etc?

Has this happened to anyone before?

Link to comment
https://www.sau.com.au/forums/topic/103597-power-fc-pinging/
Share on other sites

the first step would be to isolate what load point its coming from, clear the max knock value, plod arond and see if it spikes up again. if it does then its in the low load area (unlikely). clear the max again and do some medium cruising and check the max knock (likely to be the cause). then try some heavy driving and see if knocks consistently. if you are able to reproduce it try IGN/INJ retard a few degrees of timing and see if that helps it, if so its just a few load points where the timing is too high. if you can make the knock go away by taking out a few deg then get a friend to drive and punch it, watch map tracer and wait for engine flash to come on and pick what cell is doing it, then goto IGN and back out a few degree's for that cell. you should narrow it down within about 5 minutes of doing this.

dyno tuning is fine but road driving does change the load a little, for example going up a slight hill in 3rd will have different load variances to a fixed dyno if that makes sense. nothing to be worried about just a few points need to be smoothened out on the road.

nice power you made, thats on the gt-rs yeah ? good stuff :)

Paul/R31 it does not knock all the time. most of the time i boot it and its fine but sometimes the light comes on. The laptop read very low knock levels so im not surew which to believe. The mechanic and tuner said there was definately no knock but the sensor says otherwise.

Yeah making 260rwkw on GTRS on 17psi with more in it. They still have not played with the exhaust cam as my exhaust manifold (one of those stainless ones) cannot flow enough and boost begins to spike. Next step is to get a custom manifold and go for 20psi :P

you generally dont hear the ping @ an audible level while driving.

I reckon it'll be just one cell or two thats causing the problem.

Its very easy and common to happen as dyno/street are different.

You arent say... riding @ 4000rpm then planting it on a dyno etc.

Just different conditions which... probably a cell or two :P

im tending to think my sensor is just picking up engine noise and is too sensitive. I cant hear any pinging so it should be ok?

What R31Nismoid just said, you can't hear audible detonation and thats what kill's engines.

Do what paul said try taking a few deg out on the overall correction to see if it makes a difference.

Also the load on a dyno can be a little differnt on the street, i've seen up to 3 load point change from what was being read on the dyno.

just had my car tuned made 265rwkw on 17psi. On the dyno using the lap top software the car registered no pinging (30-40 on full load). Now we took it for a drive on the road and its making 140 knock on the hand controller.. im puzzled!

I'm surprized they tuned it with knock that high on purpose :P

After my tune I too had a little knock when jumping hard on the throttle at around 4000rpm.

I think you'll find that it is most likely slightly overboosting into a cell that would'nt have had an overboost situation on the dyno run.

how much timing in the tune...

usually knock levels around 20 at full boost and high in the rpms is your goal on the dyno. as when you drive it on the street knock levels increase as street driving has different load....

i would say the tune is to agressive....timing is not the only thing that makes power.....

hope this helps.

same here, tuned my car on the dyno, 20 knock, and then took it to the street and pinged up to 80 - 100.

Dyno's don't load the car as much as the road.

Get it re-tuned. Or DIY the ign retard on the street if you have a datalogit.

i have the same problem, genrally in 3rd 4th boosting up a hill...

i think my car is going slower and the engine is making a groaning noise.

i wouldn't do this too much, if you can hear the engine straining downshift or something

I think you'll find that it is most likely slightly overboosting into a cell that would'nt have had an overboost situation on the dyno run.

I had the knock on the street when mashing it around 5000rpm in 3rd.

It certainly wasnt over boosting... just one cell had a slightly off value.

Its really a 5 mins (at the worst) fix if you can remember approximates of what RPM/Speed/gear and throttle position (usually WOT) then the tuner can work that out no worries

Just had it out last night. No problems at all. reving it hrd as and knock didnt go over 11. seems ok. no idea maybe cause of the heat?

pretty much.

As i said (a few times) it'll be one or two cells that have a slightly higher ignition value.

Next time it happens, note down roughly what speed/rpm/gear etc and tell your tuner. Should be able to fix it and it'll never happen again, heat or otherwise

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A little more work this week.  Fitted astra power steering pump in the boot with a lowe fabrication bracket. Gave the pump a good clean, fitted Anderson plug and high pressure fitting. With the intercooler being flipped under rad support factory headlights weren't going to work. Ordered a set of origin battle lights, they arrived so got them test fitted. Will require some fiddling to fit nice but was an easy quick option for now. And today we pulled out the manual Rb gearbox and test fitted a ZF 8HP50. It will fit with some casting tabs cut off and small tap of the tunnel with a hammer. Pick up the adapter plate Wednesday so hopefully all bolted in Friday and measure for tailshaft which will be a 2 piece. Been doing a lot of ecu, pdm and tcu loom design so when comes to wiring it in a few weeks will all go smoothly.
    • FYP. Sadly. Even bolt cutters wouldn't take 2 sec. But in the days of 18v angle grinders, nothing is safe.
    • One piece driveshaft I would recommend a dual CV setup otherwise stick to OEM. I have heard most one piece driveshafts cause excess vibration otherwise. The transmission grind I'm quite familiar with. You can try shockproof gear oil, otherwise you need a new transmission. The shifter is extremely simple on these cars. If you want pull apart the assembly and replace the plastic bushing but I doubt that fixes anything. The tail light issue is very common, unfortunately new tail lights are long discontinued. The trunk antenna going up always is because your radio doesn't have a true power antenna control, just remote amp power signal. There is a blank switch plate that you can pop out and install a switch for this or alternatively source a head unit that has proper antenna control. Throttle body sticking you have to disambiguate by disconnecting the cable and seeing if the linkages are the problem or something else. There is a procedure to adjust them, refreshing them is also somewhat involved if that's the issue. I have dealt with many of these issues. Old cars really are fractals of problems. The more you fix the more you discover there is to fix.
    • Welp, you've got a long list of experiences right there. I'd say you're on the right path.
    • That's correct, suits my requirements a bit better. Sure there are also numpties there, however it's generally a different vibe and more my kind of vibe.
×
×
  • Create New...