Jump to content
SAU Community

Worst Engine Noise Ever!

Psymon

By Psymon,
in Car Audio & Electrical

 Share

Recommended Posts

Psymon Mentor

Psymon

Posted
Posted

Was out cruising last night and i hit a rather nasty bump. As soon as i hit the bump my stereo developed a really nasty engine noise whenever the ignition is switched to ON.

I checked all the wiring at the amp and it is all fine. Could the rca's be shorting against the body of the car somewhere to cause this noise? Or could it be wiring at the back of the head unit coming loose?

I tried a ground loop isolator we had lying around at work today and it didn't make any difference.

If anyone has any ideas please let me know as driving around without music is driving me insane!!!

Thanks

Link to comment
https://www.sau.com.au/forums/topic/103674-worst-engine-noise-ever/
Share on other sites
Crimpage Community Regular

Crimpage

Posted
Posted

If it was RCA's shorting, it would probably make a scratching noise where as "engine noise" is a whirring sort of sound that you will notice is in time with the car's RPM.

Things to check for:

1. Power cables too close to RCA's

2. Check that you have earthed the amp's properly. make sure to scratch away the paint underneath any amp mounting points. Apparently vaseline is good to help with earth conduction and also help prevent it rusting where you have removed the paint.

3. failing all that, try getting a noise suppressor for the altenator.

Crimpage.

  • 1 month later...
frx026 Proficient

frx026

Posted
Posted

Hi Psymonm

There are a few things that it could be, i would start be checking the following.

- Earthing points for your amplifiers - make sure they are clean and not loose at all.

- Earthing points for your head units

- Earthing points for your battery.

- Amp Power cable connection to your battery

- RCA connection at head unit and at amp

- RCA path to rear of car - especially under the back seat, they may have become pinched, cutting through the insulation and them allowing inducted or radiated noise in.

These are a few of the obvious ones.

really it is just a trial and error thing, there is no real one hit solution to engine noise as every car is different.

Good luck with it.

Regards

Pj

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Stock rb25det neo questions

      By GTSBoy · Posted

      While it is a very nice idea to put card style AFMs into the charge pipe (post intercooler, obviously), the position of the AFM and the recirc valve relative to each other starts to become something that you really have to consider. The situation: The stock AFM is located upstream the turbo, and the recirc valve return is located between the AFM and the turbo inlet, aimed at the turbo inlet, so that it flows away from and not through the AFM. Thus, once metered air is not metered again, neither flowing forwards, or backwards, when vented out of the charge pipe. When you put the AFM between the turbo outlet and the TB, there is a volume of pressurised charge pipe upstream of the AFM and there is a volume of pressurised pipe downstream of the AFM. When the recirc valve opens and vents the charge pipe, air is going to flow from both ends of the charge pipe towards the recirc valve. If the recirc valve is in the stock location, then the section between it and the TB doesn't really matter here - you're not going to try to put the AFM in that piece of pipe. But the AFM will likely be somewhere between the intercooler and the recirc valve, So the entire charge pipe volume from that position (upstream of the AFM, back through the intercooler, to the turbo outlet) is going to flow through the AFM, get registered as combustion air, cause the ECU to fuel for it, but get dumped out of the recirc valve and you will end up with a typical BOV related rich spike. So ideally you want to put the AFM as close to the TB as possible (so, just upstream of the crossover pipe, assuming that the stock crossover is still in use, or, just before the TB if an FFP is being used) and locate the recirc valve at the turbo outlet. Recirc valve at the turbo outlet is the new normal for things like EFRs anyway. In the even of a recirc valve opening dumping all the air in the charge pipe, pretty much all of it is going to go backwards, from the TB to the recirc valve near the turbo outlet. But only a small portion of it (that between the TB and the AFM) will pass through the AFM, and it will pass through going backwards. The card style AFMs are somewhat more immune to reading flow that passes through them in reverse than older AFMs are, so you should absolutely minimise the rich pulse behaviour associated with the unavoidable outcome of having both a recirc valve and an AFM in the charge pipe.
    • joshuaho96
      Rb25det Belts Change

      By joshuaho96 · Posted

      Yep, in my case as soon as I started hearing weird noises I backed off the tension until it sounded normal again. Delicate balance between enough tension to avoid that cold start slip and too much damaging things.
    • silviaz
      Rb25det Belts Change

      By silviaz · Posted

      nvm this comment
    • silviaz
      Rb25det Belts Change

      By silviaz · Posted

      I'm almost at a point where I feel like changing the alternator. Need to check the stuff you mentioned first though.
    • Wazmond
      Stock rb25det neo questions

      By Wazmond · Posted

      @Dose Pipe Sutututu I read your replies RE: R35 GTR MAFs, any ideal spots to put on? Obviously will need the adapter plate. Will be having a cross over intercooler fitted shortly, would putting it a bit before the TB be okay?
×
×
  • Create New...