Jump to content
SAU Community

Recommended Posts

morning all.

i spent some time on sunday making a cold air induction for the cressida, utilising a chaser head light so that i could have a cold air scoop but also have lighting on that side of the car. at the last SC meet i had major problems with intake temps of 72 degree cel, as my air filter sits in the only location i have room for it in my grandpa designed engine bay, so i am looking to get some cooler air into it.

upon reading my sport compact rule book it says must run complete headlight. i asked around at the last round in sydney, and i got mixed interpretations of the rule.

one frame of mind was as long as there was lighting on that side of the car it was ok.

the other was, if you dont have the glass and bulbs in all areas of the headlight that it came from the factory its not a complete headlight.

i know i spoke to paul about this and another guy in our class who had a bulb and also an air duct in the headlight, and i think if there is lighting it should be ok.

has anyone got any ideas on this rule or have they spoken to ohalleron about it?

any thoughts would be appreciated.

Shane.

Link to comment
https://www.sau.com.au/forums/topic/103819-srwd-rules/
Share on other sites

well cow girls.

after a lack of banter on the topic i emailed jason ohallaren.

the complete headlight is defined as complete

ie full glass, bulb in full working order as it is from the factory. so for all point scoring rounds cars in S/RWD must have a complete functioning head light.

screws up my plans for my cold air, but i will find a way.

Shane

Link to comment
https://www.sau.com.au/forums/topic/103819-srwd-rules/#findComment-1918533
Share on other sites

well cow girls.

after a lack of banter on the topic i emailed jason ohallaren.

the complete headlight is defined as complete

ie full glass, bulb in full working order as it is from the factory. so for all point scoring rounds cars in S/RWD must have a complete functioning head light.

screws up my plans for my cold air, but i will find a way.

Shane

Jason is right

Rule no. SR 7.6

Complete headlight and taillight assemblies mandatory; must be operative.

Edited by DiRTgarage
Link to comment
https://www.sau.com.au/forums/topic/103819-srwd-rules/#findComment-1920725
Share on other sites

Do S/RWD rules allow you to disable factory fitted power steer?

Rule SR 3.2 Must retain full, original OEM steering gear.

I have only tried disabling power steer once at the track...it was no real benefit other than giving my forearms a good workout.

Edited by DiRTgarage
Link to comment
https://www.sau.com.au/forums/topic/103819-srwd-rules/#findComment-1920765
Share on other sites

Who knows...but my p/steer is staying

Bit confused here, why are you worried about S/RWD rules allowing you to disable factory fitted power steer then?

you planning on stripping the car when you race, I wouldn't worry about it my 10.5 was done with a fullweight car + some due to surge tank, big single turbo etc

Link to comment
https://www.sau.com.au/forums/topic/103819-srwd-rules/#findComment-1921811
Share on other sites

Bit confused here, why are you worried about S/RWD rules allowing you to disable factory fitted power steer then?

you planning on stripping the car when you race, I wouldn't worry about it my 10.5 was done with a fullweight car + some due to surge tank, big single turbo etc

I'm not planning on it...if I go to the drags again, I will run in the same trim as I have always done.

* Full weight, including all trim, spare wheel, tools and jack

* Street Tyres

* Full exhaust (a quiet one at that)

* Stock Airbox

* At least 3/4 tank fuel

Link to comment
https://www.sau.com.au/forums/topic/103819-srwd-rules/#findComment-1921843
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Shove more foam in it as a minimum if you possibly can. Or steel wool (not the stuff with soap on it!) Baffles / getting the oil out of the air is huge, and should be done at both the cam cover, and the catch can.   I'm about to do a power steering reservoir, and even that needs some thought to make sure air is separated from the oil, to stop evil Cavitation. I'll probably look at doing my own catchcan later on too.
    • I was once told, who it was I'm to old to remember, that the length of the OEM wheels brace supplied with a vehicle is designed long enough for a average person to apply enough torque to do up, and undo the wheel nuts to the specified torque  What a average person is is anyone's guess though, i.e. average fat bastard, average knuckle head, average perfect sized human......like me Unless of course, a tyre shop has ugga dugga'd them up to "torque to yeild/strip" specs, used cross threading as natures lock tight, or a big breaker bar was used to tighten them up to get some nice stretch in the poor old wheel studs Me, I torque wheel nuts to 1 elbow joint click, lower torque settings are based of wrist clicks, higher torque settings are based of shoulder clunks, or total dislocation for anything that requires all of the torques 
    • I think the catch can design is pretty flawed. Evident in the fact that the V2 one moved to a larger top mounted filter which alone would have helped with overflow and reduce restrictions compared with the side filter. I also imagine there was a major improvement to the baffling design. It is worth mentioning that this catch can with the RB20 was never as much of an issue and the high kms RB25 is likely a part of the problem. I have gotten quotes for both a new "Vibrant Gen 3" catch can and to modify this existing ones but that may have to wait until after the track day. I hope the sump/head breathers/drains and cam splash plates will be enough
    • Yep, both. The ratio is 1.8 instead of OEM being 1.7. The rocker bodies are modified with a larger bolt hole and re-threaded with 10mm holes instead of the 8mm YT has stock. Finding out they don't actually fit the stock castings cause a lot of un-impressment by the person in the USA who tapped the new holes for the 'upgraded' YT product. He was very unhappy with them given their previous design did not require 'clearancing'
    • That too, but I think this is why she's put the work into the cam cover baffles. I mean, a catch can should only need to be a catch can, not an oil air separator also. Not to say that putting the effort into having it do a better job of oil-air sep is a waste of time, but doing the sep earlier is always going to make life better. And that should happen now anyway.
×
×
  • Create New...