Jump to content
SAU Community

Rb30 Hybrid Upgrade, All Dyno Results

R31Nismoid

By R31Nismoid,
in Engines & Forced Induction

 Share

Recommended Posts

Pridenjoy Apprentice

Pridenjoy

Posted
Posted (edited)

Hi guys,

I recently finished my forged 25/30 all built and wired up the my garage by myself.

Parts consist of:

Mahle 86.5 pistons @ 8.5:1 cr

spool rods

arp gear throughout

nitto oil pump. using one 1.5mm restrictor, with the other blocked.

vct internal feed

ross race balancer

complete bottom end balanced

rebuilt head with std cams and valves

Performance valve springs

1.0 mm cometic headgasket

ebay inlet manifold 90mm tb

aeroflow fuel rail

1400cc injectors

ls2 coil plugs mounted as coil on plug

hybrid exhaust manifold

kinugawa t67 with t04 compressor

turbosmart 45mm gate

turbosmart boost solenoid

3in straight through exhaust

walbro 460

haltech ps2000 with racepak dash

currently on its run in tune, 288kw @ 17psi and only reving to 6k rpm on bp98

post-116505-0-22065400-1432201637_thumb.jpg

Edited by Pridenjoy
Link to comment
Share on other sites
  • Replies 271
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

whatsisname
whatsisname

Video of one of the dyno runs: It made 525kW at 27-26psi. We then turned the boost up to 29psi and on the next run just as it passed through 545kW the compressor outlet pipe clamp let go at about

lcxu105
lcxu105

Had it back on the dyno on Monday to check the tune as someone at a repair shop had f**ked around with it without permission.  Played with the e boost controller a bit and rolled out 628rwhp with

whatsisname
whatsisname

Upgraded the main and head studs, switched from Splitfires to an R35 coil kit to solve the misfiring above 25psi, and added a few other things. Upped the boost to 29psi and made a few extra kilowatts

Posted Images

Nismo 3.2ish Grand Master

Nismo 3.2ish

Posted
Posted

Forgot to post the final tune. After all the waiting, the end result is a little disappointing, expected a bit more grunt, but not over yet, a few things to sort out .

Going to beef up the fuel and exhaust.

Flex tune and see how it goes.

post-52098-0-09875000-1432205043_thumb.gif

Link to comment
Share on other sites
Leithy Enthusiast

Leithy

Posted
Posted

Mods rb25/30

Hks 272 cams

Garrett gt3582 anti surge

Sard 850cc injectors

Self made turbo manifold and 3 inch exhaust

45mm hypergate

Freddy manifold

Splitfires

Still has a boost leak through the throttle body shaft

post-74608-14324603610343_thumb.jpg

post-74608-14324605295024_thumb.jpg

Link to comment
Share on other sites
  • 1 month later...
Huzqld Enthusiast

Huzqld

Posted
Posted

RB25/30 NEO

Spool rods

wiseco pistons

Balanced

Arp everything

N1 pump with billet gears and oil relief setup. and longer crank drive collar

ASR 8.5L sump

Standard head with 270-9.2mm cams no vct

performance valve springs

6x LS2 coils

cpc plenum

steampipe manifold

GT35 .82 rear internal gate

660CC injectors

420hp @22psi injectors at 85% duty cycle

Also couldn't get it to hold more boost up top (could of wound the pre-load up but decided against it)

BP98 fuel

Auto

post-78438-0-13197000-1435543598_thumb.jpg

Link to comment
Share on other sites
  • 3 weeks later...
DCIEVE Mentor

DCIEVE

Posted
Posted

RB 26/30

BW S362 / 88-75

Fullrace twin scroll manifold

270deg cams

etc....

Dialled cams for low down at the cost of some top end. Boost is only 17psi while I get used to it, so there's a lot left in reserve.

0E5CABF9-BB4D-4833-86D0-457E5070507E_zps

  • Like 1
Link to comment
Share on other sites
  • 3 weeks later...
AndyStuttgart Enthusiast

AndyStuttgart

Posted
Posted (edited)

RB30 bottom end, RB26 head

Forged rods / 86mm Wiseco RB26 pistons, CR about 8.7:1

HKS Step 1 cams 8.7 lift, 256in 264ex, exhaust mildly ported

ID1000

RawBrokerage T4 twinscroll manifold with two Tial F44 WG (1 Bar spring presure)

EFR8374 1.05AR twinscroll

3.5" exhaust

45mm screamer pipes

Made over 600hp on wastegate pressure:

post-30656-0-75662100-1438717840_thumb.jpg

700 with manual bleed valve (unstable boost dropping to 1.45 bar at redline)

post-30656-0-02418000-1438717848_thumb.jpg

95 octane pump fuel (as setup will go to the states next year in a R32)

Video:

Edited by AndyStuttgart
Link to comment
Share on other sites
  • 2 weeks later...
Nismo 3.2ish Grand Master

Nismo 3.2ish

Posted
Posted

Just had the first run in tune, not sure what I am going to get when it has the final tune, I will post the results. They said it was at 7500RPM ?

Nitto 3.2 Stroker Kit

PT6262 turbo

Custom 260 10.8 cams,springs and retainers

Haltech 34GTR ECU/Boost controller

3.5 inch custom exhaust ( as a DD as quiet as it could be without restricting flow)

Supertech 1 mm OS Valves set

RB 26 head, cleaned up

9Lt sump conversion/ Nitto comp Pump

Koyorad Radiator

Walbro 460Lt fuel pump, (see how it goes)

Haltech E-Flex Sensor kit

Other stuff needed to make it all work

Yokohama AD08R

Nismo Super Coppermix twin C Spec clutch / Slave Cylinder

Quaife Front diff

Modified Trannie

Nismo 2-way LSD back diff

t run in tune, not sure what I am going to get when it has the final tune, I will post the results

Just leaving the final Dyno to finish my tuning experience :)

98 pump@ 22psi = 437kw

E85 @ 22 psi = 462kw

E85 @ 25.5 = 475kw

Other Dyno is overlay of old tune 98 pump 367kw @ 22psi and new tune on 98 pump 437kw @ 22psi

post-52098-0-45066100-1439635319_thumb.jpg

post-52098-0-22397600-1439635813_thumb.jpg

  • Like 1
Link to comment
Share on other sites
684NGR33 Apprentice

684NGR33

Posted
Posted

-Freddy copy plenum

-id1000cc injectors on big rail

-Sard fuel pressure reg

-Spitfire coil packs

-China replacement turbo

-Adaptonic computer

-Rolling automotive front mount

-80mm throttle body

Made 305.5rwhp (227.4kw) on 15psi

Tubos shit. Will make more with a quality turbo.

post-139776-0-43569300-1439903618_thumb.jpg

post-139776-0-61680400-1439903797_thumb.jpg

Link to comment
Share on other sites
  • 2 weeks later...
danny14 Mentor

danny14

Posted
Posted (edited)

26/30

E85 2000 cc inj

Twin bosch 044s and surge tank

Haltech platinum plug in

Gtx 35 1.06

Ported kelford cnc head

Kelford heavy valve springs etc

Tomei head gasket

Arp head studs

Kelford 272 274 10.85 lift cams

Rips stock bottem end with prep upgrade

Tomei oil pump

Rips 10l L sump and gredy oil cooler

426 kw at all 4

26 psi

Edited by danny14
Link to comment
Share on other sites
  • 2 weeks later...
Fantm 34 Explorer

Fantm 34

Posted
Posted

RB 25/30 Neo running E85

435 rwkw @ 23 psi

Nitto I beams

Custom CP pistons 8.8:1

Garrett GTX 3582 1.01 exh

Tomei 260 type B poncam

Mild port/polish head

Tomei dual spring and retainers

1500cc ID injectors

Walbro 460 intank twin 044 from surge tank

3" straight thru stainless exgaust

Custom stainless header

NPC twin plate

Retained VCT

post-46346-14416299316189_thumb.jpg

Link to comment
Share on other sites
  • 3 weeks later...
steve200b Proficient

steve200b

Posted
Posted

attachicon.gifImageUploadedBySAU Community1410860879.685567.jpg

Gtx3076

Tial 44mm ext gate off housing

Lt12 ecu

Eboost street

850cc injectors

Hks 256 in 264 exh vct cams

Hybrid manifold

Forward facing plenum

Precision cooler

All through a built r34 auto with 3000 rpm converter

15psi boost

E85 and lt16c computer next month

post-84952-14434350682349_thumb.jpg

E85 lt16c Ecu 6boost manifold upgrades.

  • Like 1
Link to comment
Share on other sites
  • 2 months later...
Pridenjoy Apprentice

Pridenjoy

Posted
Posted (edited)

Hi guys,

I recently finished my forged 25/30 all built and wired up the my garage by myself.

Parts consist of:

Mahle 86.5 pistons @ 8.5:1 cr

spool rods

arp gear throughout

nitto oil pump. using one 1.5mm restrictor, with the other blocked.

vct internal feed

ross race balancer

complete bottom end balanced

rebuilt head with std cams and valves

Performance valve springs

1.0 mm cometic headgasket

ebay inlet manifold 90mm tb

aeroflow fuel rail

1400cc injectors

ls2 coil plugs mounted as coil on plug

hybrid exhaust manifold

kinugawa t67 with t04 compressor

turbosmart 45mm gate

turbosmart boost solenoid

3in straight through exhaust

walbro 460

haltech ps2000 with racepak dash

currently on its run in tune, 288kw @ 17psi and only reving to 6k rpm on bp98

UPDATE...

After the engine was ran in I strapped it down again which it made 320kw on 20 psi, and having iat problems.

I then fit a new plazmaman intercooler and ran it on the dyno with pump e85 making 374kw on 21psi, which is all the little t67 will do.

post-116505-0-55881400-1448771813_thumb.jpg

Edited by Pridenjoy
Link to comment
Share on other sites
  • 3 weeks later...
acsplit Veteran

acsplit

Posted
Posted

Ok about time I posted in here..

Racepace Built RB26/30

Mahle 87mm forged pistons

Argo Rods

HKS 256 8.5mm lift cams

adj cam gears

Sard 700 cc injectors

Tomei Oil pump

Tomei Headgasket

Std Coilpacks

Std Valves and head

Power FC

3.5" Racepace custom exhaust

Walbro 255 pump

Garret 2860r-5 Turbo's

HPI dump pipes

Std manifolds inlet and exhaust

R33 GT-R intercooler

Std R33 GT-R Airbox

Balanced Blah blah

375rwkw @ 17 psi BP 98 (369 for the track)

post-723-0-21640500-1450217298_thumb.png

post-723-0-68835200-1450218003_thumb.jpg

  • Like 1
Link to comment
Share on other sites
  • 2 months later...
Pezhead Grand Master

Pezhead

Posted
Posted
Very similar build spec and result to acsplit above.
My goals are for a responsive track car I can daily on 98 - drive and fill up anywhere.
RB30 Bottom end w/ Ross Racing Pistons & Spool forged rods
Garrett 2860 -5 Twin Turbos
Tomei Expreme Dumps
Low comp 7.85:1 (to keep things safe on 98, YES I'm staying 98 for a while)
ARP M11 Head Studs
Nismo 0.9mm Metal Head Gasket
+1mm Supertech valves with Supertech springs & retainers
Tomei Pro Cams 260 10.25mm lift
ID 1000 injectors
Autronic SMC / 500R CDI (Super Old School!) firing through Splitfire coils
Adj cam gears
Nitto Oil Pump
Single 044 pump & 2L surge tank

12791116_1183587054999874_67586165268249

  • Like 1
Link to comment
Share on other sites
  • 3 weeks later...
whatsisname Grand Master

whatsisname

Posted
Posted

Had the car on the dyno today.

Still early stages at the moment. Just finished running-in new the RB25/30DET. Timing and fuel is conservative, purely as we ran out of time in the day to make improvements.

A quick power run on 22psi (E85) resulted in the following:

post-81-14588172696437_thumb.jpg

411kW at wheels on just shy of 20psi

428.8kW at 22psi

Aiming to run up to 30psi

Link to comment
Share on other sites
Nismo 3.2ish Grand Master

Nismo 3.2ish

Posted
Posted

Just leaving the final Dyno to finish my tuning experience :)

98 pump@ 22psi = 437kw

E85 @ 22 psi = 462kw

E85 @ 25.5 = 475kw

Other Dyno is overlay of old tune 98 pump 367kw @ 22psi and new tune on 98 pump 437kw @ 22psi

Update

Decided to go V-Cam :)

Lost a little up top, but it the injectors and Turbo were just about maxed, all good

The end, I hope :/

post-52098-0-49782600-1458846669_thumb.jpg

  • Like 1
Link to comment
Share on other sites
whatsisname Grand Master

whatsisname

Posted
Posted

Had the car on the dyno today.

Still early stages at the moment. Just finished running-in new the RB25/30DET. Timing and fuel is conservative, purely as we ran out of time in the day to make improvements.

A quick power run on 22psi (E85) resulted in the following:

attachicon.gifImageUploadedBySAU Community1458817268.954023.jpg

390.3kW at wheels at 18psi

411.1kW at 20psi

428.8kW at 22psi

Aiming to run 30psi

Video of the 22psi run:

https://m.youtube.com/watch?v=VhnlYVwQlBg&feature=youtu.be

  • Like 2
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • r32-25t
      GReddy Injector Help!

      By r32-25t · Posted

      You need the kit turbo taipan has shown you because that manifold ia designed have side feed injectors 
    • alexburns
      Stagea Dash Multimeter

      By alexburns · Posted

      @johnnysr22 did you end up installing the little screen thingy and did it work ?>   
    • Lithium
      Boost level and torque curve

      By Lithium · Posted

      There is a LOT of stuff that can be done, it all depends on how much time and money you want to spend on doing in.  Not all ECUs will be able to do it, and the more control you need the more time and knowledge needs to be put into making it work.  If you're willing to spend the time and money and have the right hardware and skills involved there's a lot that can be done. 
    • thx78
      Boost level and torque curve

      By thx78 · Posted

      I am impressed with all this level of adjustment. I didn't expect all this possibility
    • Lithium
      Boost level and torque curve

      By Lithium · Posted

      Correct.  In the case of the 500kw dyno plot I showed you the car actually runs two boost control solenoids for boost control and a 5psi wastegate spring.  It allows me to control how much boost pressure is applied to both sides of the wastegate valve at any point and fairly accurately control boost target as a result. I've tuned it so that it's able to target anywhere from 5psi to 25psi depending on what's needed.  The target tables I've set up in that car are Gear vs RPM, so every gear has potential for a different boost (and torque) curve.   First and second gear have quite low boost targets, third gear actually has different target boost all the way through the rpm range as it's a stock RB25 gearbox - the boost targets have been chosen to maintain a peak of 600nm (what the owner has set as the maximum torque he's happy with putting through the stock 3rd gear) but it carries that to the rev limiter.   The boost curve to achieve that is something of a ramp up, then hold, then ramp up again and the power curve looks more like a flat line haha.  
×
×
  • Create New...