Jump to content
SAU Community

Recommended Posts

  • 1 month later...

Here is my result only running 8psi for run in tune. Motor is a 2630 forged bottom end, built head fully ported oversize valves ect. Running a forced performance super 94 with 1.14 exhaust housing on 6boost t4 twin scroll 4" exhaust also haltech plug-in pro on e85

20160831_173822.jpg

  • Like 2
ImageUploadedBySAU Community1405245838.185875.jpg

140000km bottom end

N1 oil pump

Std rb25det head with internal vct mod

850cc injectors

Greedy copy inlet manifold

Hybrid exhaust manifold

Precision turbo intercooler

Gtx3076r .82 rear with tial 44 mm gate of the snail

Eboost street

16psi 285kw through an auto with cam issues. Time for an adjustable exhaust wheel to see what happens


e4346d19286ef53e7babf4d51f8333ab.jpg
Retune with gtx3582 at 23psi
  • Like 2

 

Spool and CP bottom end with extended crank collar and billet gear pump

R33 S2 head with Tomei 256掳 cams and internal VCT mod

RIPS intake, 6Boost mani, 50mm gate and ProBoost GTX35 (.82 rear)

A1000 pump, 1200 FPR, 1200cc injectors

Haltech plugin with 3bar MAP, Air temp and Wideband

LS2 coilpacks

Running 98 for the moment

WP_20160808_19_58_31_Rich.jpg

WP_20160808_19_59_25_Rich.jpg

  • Like 2
  • 3 weeks later...
  • 1 month later...

What power would i be making roughly ?

rb30 standard block

rb25 head 262 cams 

fully forged internals

gtr3788r turbo 40mm gate

1000cc injectors

twin 044 bosch fuel pumps

front mount 

turbo back 4 inch dump to 3.5 

ffp and all other small mods 

 

Edited by ncrdbl
more to add
14 hours ago, ncrdbl said:

What power would i be making roughly ?

Dude, this is the COMPLETE OPPOSITE of results.  This is for sharing results, not asking what it should make.  Get it tuned, share the result and then we'll all know the answer :)   If you want to discuss the setup or how well its matched or should perform, start a suitable thread.

  • 3 weeks later...

Hi all...recently tuned my; 

Vl turbo with RB30/25 neo head

- Built bottom end - forged pistons, rods, N1 oil pump, studs 

- Ported head- type B tomei poncams, 

- Front mount intercooler 

- Forward facing plenum

- 2 x 044 fuel pumps

- 6 boost manifold 

- GTX 3582

- Bosch injectors 2000's

I have been building this car for years which has been an ongoing project/hobby... it's a 5 speed manual, running 24 psi on e 85. 

 

 

 

Screenshot_2016-12-09-23-06-12.jpg

  • Like 3
18 hours ago, Rb30/25 said:

Hi all...recently tuned my; 

Vl turbo with RB30/25 neo head

- Built bottom end - forged pistons, rods, N1 oil pump, studs 

- Ported head- type B tomei poncams, 

- Front mount intercooler 

- Forward facing plenum

- 2 x 044 fuel pumps

- 6 boost manifold 

- GTX 3582

- Bosch injectors 2000's

I have been building this car for years which has been an ongoing project/hobby... it's a 5 speed manual, running 24 psi on e 85. 

 

 

 

Screenshot_2016-12-09-23-06-12.jpg

What comp ratio as this buid is almost exactly the same as mine. i have 1000cc injectors thats all that is different and ecu.

I have 9:1 compression and microtech....the combo works well

3 hours ago, lcxu105 said:

What comp ratio as this buid is almost exactly the same as mine. i have 1000cc injectors thats all that is different and ecu.

  • 2 months later...

Not sure why I never got around to posting in here since I've had an RB30 in the stagea for 8 years now....just got it back from Unigroup after they sorted an exhaust restriction so I thought it was time to post up

This is from my rb30 stagea

* Rb30 bottom end with forged pistons and rods

* Standard stagea head

* eboost 2 @ 19psi high boost

* Garret GT35R with 0.63 housing (the baby one)...I think!

* Generic front facing plenum and stainless high mount manifolds

* Larger injectors but stuffed if I know what size or brand.

It makes 200awkw @ 4000rpm and 250@6250 with 19psi. Comes on nice and early which is what I was after.

stagea-dyno-2016.jpg

  • 1 month later...

GTX3584RS 1.01

26psi

Max of 7800rpm

 

There is more in it but decided to leave it there for reliability and longevity. I have no doubt 30-32psi would deliver 560-570kW, possibly more.

 

Made 421kW at about 19psi - lazy curve whilst setting up boost control, so 10psi slowly creeping up to 19ish

 

IMG_8080.JPG.e96f6811e1ba4f82eb844b9502afefc0.JPG

 

  • Like 2
  • 1 month later...

RB3025 Neo

-260deg 9.15 poncams                     - GT3076 0.82rear with 44mm tial, 3 1/2 inch exhaust, 100 cell cat, Sinco topmount                                    - walbro 416l/ph , 1000cc x spurts   - p fc, AVC-R , E85

- Injectors at 85%, pump almost maxed plus other parts at limit, maybe a play with cam gears later but it pulls hard already.

 

         

 

                                                                                             

20170526_221840.jpg

 

Edited by AngryRB
  • Like 1
  • 2 weeks later...

Worked on the boost control set-up, added 1psi in the mid range, and a bit more (1-2degrees) timing up top.

Dyno overlay isn't 100% accurate but it's close enough

Results:

IMG_8573.JPG

  • Like 1
  • 2 months later...

R33 series 2

Head: Rb25de (r32) with Rb26 springs still stock cams

Block: stock o-ringed rb30de with new rings and bearings 

Turbo:garret GT3082 .82A/R exhaust housing 

ECU: microtech lt10s

Fuel: E85

stock exhaust manifold modded to fit external gate

1200cc injectors

custom inlet plenum

290ish kw @ 18psi with 799nm

funny enough made the same peak power on the same boost with this turbo on my rb25det with poncams and pump fuel

This setup has a heap more low/mid range but

 

 

dyno.jpg

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I haven鈥檛 taken them out of the cases yet    inside the box is this packaging which is pretty much like a massive blister pack 
    • Purchased a NC MX5 a while ago Basic suspension mods done, BC coils and Whiteline sway bars  New DBA calipers, discs and pads Added some 17 x 8 Konig Decagrams with 215/45 17 PS5's Added some typical NA bolt on's, i.e. full exhaust and intake  Added 0.5ltrs with a MZR2.5 swap, nice bump in torques  Found a detachable hard top which is locked in for a colour match with my local paint shop in Feb 25, this also includes some PDR as it has received a few love taps from parking in the local shops when in the hands of my Minister for War and Finances, me, I park nowhere near other cars and typically park on the street The little thing is awesome, I drive it everywhere, it handles like a dream whether I'm up it or just cruising  But now,  because I'm a idiot, I keep looking at turbo kits....... did I mention I'm a idiot Why is dose so appealing  All of the NA 2.5 glory, well.......until sometime in 2025 anyway....馃お  
    • I would not be surprised if you are the only person on earth that has the interest/desire to do that lol.  The Haltech base map is a really good starting point, the car will fire easily and drive very well, even on mild boost levels. To me, following your advice sounds like some sort of ancient Chinese water torcher lol (this is not an insult Josh, never change <3)
    • Those car show concepts from the 2000's and 2010's like the Floria and IDx were brilliant and should've gone ahead, at least one of them. But neither Honda nor Nissan are thinking about affordable performance any more, which is truly sad.  Even if Toyota's liquid hydrogen ICE development reaches the point where it's commercially viable and the infrastructure to support it, Honda/Nissan would have to wait until Toyota allow fee access to their patents to offer it with any smaller performance models they released to take advantage of it.  
    • A sporty manual RWD coupe with a IL4 Honda engine would only be a good thing I assume we won't see anything released for a few years though, unless informal talks and designs have been going on for a few years,  and due to the current, and future, emmisions and safety requirements, I assume anything "sporty" they would do would be at least some hybrid thingie And hopefully anything they are thinking of has nice lines, without lots of plastic and fake bits hanging off it like that horrendous FK8 that looked like it was designed by a 13 year old The other issue of course in the current market is cost, currently the type R is around $70k, a twin is around $50k Meh, I'm old and grumpy and would rather buy a older model car and waste my coin on that than buying anything currently available new  
  • Create New...