Jump to content
SAU Community

Recommended Posts

TURBO KIT

TRUST T88 34D Turbo kit with TRUST TYPE C wastegate to suit RB26

Front and rear housing freshly polilshed and ceramic coated respectivly

Braided oil feed Line made to suit RB26/30 combo

Dump pipe made to suit r33 gtst

Price: $4000

PRICE CHANGE $3700

FUEL KIT

HKS fuel rail to suit RB26

1000cc BLITZ injectors

SARD fuel regulator

Surge Tank

Twin Bosch 500hp pumps

Twin Billet Filters

Twin 10mm Aluminium lines

(all fittings from surge to pump to filters to rail)

whole setup has not seen 1000kms

Price: $2500

PRICE CHANGE $2300

Edited by nv033
Link to comment
https://www.sau.com.au/forums/topic/104447-complete-800hp-combo/
Share on other sites

  • 2 weeks later...
Any pics of the T88??

Why is a dump for a GTSt part of an RB26/30 package??

I'm interested in the T88 kit but not in the dump pipe.

Because the above kit went into a GTST.... The turbo in the pic has since been polished (still in wrapping) and rear housing coated

119-1912_IMG.jpg

118-1874_IMG.jpg

119-1908_IMG.jpg

119-1911_IMG.jpg

how much power can this make on a gtr motor with step 1 cams,basic mods, and 20psi boost..

can be 50rwkw off .. can this make over 400?

with the above specs it should see very close to 400rwkw above or below i cant answer because there are too many variables :) however this turbo is certainly capable of making over 400rwkw....500rwkw is more its cup of tea

to get a feel of it with the 3L @ 16psi with minimal timing it saw 370rwkw ;)

Edited by nv033

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome Alice......hope you have a bit more luck from here on! What was done in the build?  
    • Hello! I'm new here, I have an R33 GTST that is currently being finished up! Last year was pretty rough, blew two stock turbos so I decided to build the car. Has been down since November, but I get it back next weekend!
    • Hello, I believe my car was imported to America in the 2000s by Kaizo Industries. Would anyone be able to help me find more info on them? I've only found all the basic stuff like that paul walker bnr34, them being shutdown by feds, just stuff like that. Any help would be much appreciated, thanks!
    • I am using Motec M150.  I am not working on the car myself actually.  My workshop is giving all these info, they are quite reputable in the industry and are very familiar with Motec and RBs and have done a few big setups with VCam and single turbo on RBs.  In fact, they built and tuned my engine from day one.  But they are stumped with my engine at the moment and cannot work out how come the compression is so low with the VCam. They told me that they have now swapped in some Kelford cams (without the VCam) and can achieve around 130psi compression and the low end torque is better, but now the engine is doughy as.  It boosts and peaks at more than 1000rpm slower, with twin HKS GTIII RS, it doesn't get full boost until over 5000rpm. I have always thought the VCam was a bit disappointing at the low rpm. To a point I had to ride the clutch a fair bit to get up a small hill from stand still.  That was when I had a clutch.  Now changing to a 8HP, I don't have that luxury and this problem has become a major issue. I am beginning to think the VCam never work since the day it was installed.  Maybe it was just sitting at the most advanced point, that is why it went good at top end but very ordinary at the bottom.  Therefore, with the help of the Holinger 6 speed and paddle shift, as long as it was moving, it drove pretty good.
    • yeah, there's a country that recently started importing Skylines, I blame them.
×
×
  • Create New...