Jump to content
SAU Community

Recommended Posts

Hi all , firstly would like the ID Tag no's from one of these if possible .

I have found different figures for the turbines in these turbos , HKS USA site shows ~ 58 x 54mm which sounds like a mildly cropped GT30 turbine . Some pics I found from a string at Performance Forums shows the turbine at 63.99 x 58.8 mm which is basically GT32 turbine dimensions in 84 Trim .

The compressor is shown as 82.46 x 60.64 so 54 Trim .

If anyone has one of these turbos would it be possible to measure the wheels even if from the outside of the housings to confirm the sizes .

The difficult thing to know is whether HKS got Garrett to crop a 68mm GT35 turbine or used a GT32 turbine with the GT30 or 35 sized shaft and bearing pack .

Either way you could say the HKS GT3240 is a slightly reduced optomised GT3540R ie with slightly smaller trim compressor and turbine mid way between GT30 and GT35 to pick up the response . I think its power rated at ~ 570 ps where the GT3540R is around 700 Hp , 700ps ?

If all my assumptions are correct , with a suitably sized (a/r) and T3 flanged turbine housing this would suit many that are asking for more than a GT30R can give with less lag than a GT3540R would have . Typically HKS want to charge a lot more for something thats a little less for their "Power and Response" monica ...

Cheers A .

post-9594-1139186666.jpg

post-9594-1139186795.jpg

post-9594-1139186879.jpg

post-9594-1139187008.jpg

Link to comment
https://www.sau.com.au/forums/topic/104680-hks-gt3240-id-and-details/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I'm firmly on the "zero compliance is good compliance" for FUCAs. I'd be looking to solid metal joints even if the primary reason for having them is because they facilitate the twist in the arm. I have never been more happy with the way the front suspension behaves than I have since I got rid of the FUCA bushes. Even the thin little (short lived) poly bushes in the Whiteline adjustables have too much compliance for my liking. It probably won't be long before I have sphericals nearly everywhere, probably including both top and bottom arms in the rear, and I'll start complaining about the increased costs for dental work. But I will be enjoying the driving more, I'm sure.
    • Plus, you'll get great experience in bedding in pads!
    • I have offset Nismo brackets so the fact the gktechs can pivot is less important to me. I have 170mm JIC arms with bushings - but they provide no adjustment and I'm not sure whiteline eccentric bushings will fit them (I don't want to ruin the bushings currently in them to find out). Ideally I want something with bushings + adjustment; hence why I'd like to find a pair of these. Unfortunately they aren't easy to find.
    • @Vee37 How much do you really care about finding these pads again? If your pads are quiet, work well and produce minimal dust, really isn't that enough? If you are set on finding the exact pads again, I suppose I'd do something like this -  Visit your local Jax, find out what brand of pads they carry. If the Jax workshop you previously went to had the pads on the shelf, then you can almost guarantee it will be of said brand.   I'm guessing you don't have the receipt for the previous work and pads. Can you visit a Jax workshop and see if they can look up your previous job to see what pads were fitted?  Still no luck? Put your stalker hat on, find the staff that used to work at the Jax store and ask them. Talk to local workshops, try to find out where the mechanics went to. Talk to Jax workshops, maybe they relocated to another workshop. When it comes to mechanics, its a small world. You'd be surprised how easy it is to track someone down. If these ideas don't work, shit will start getting crazy very quickly.... You could find out every brand and model of pad that fits that car... and try them individually ticking each off the list if it wasn't the one you were looking for.... If you go down this path your going to want to learn how to swap pads yourself, it is very easy, takes minimal tools and space. If you have room to park the car you have room to swap the pads. Plus you have the advantage of making sure all the brake hardware goes back in so they won't squeal! 
    • You miss spelled bearings...
×
×
  • Create New...