Jump to content
SAU Community

Recommended Posts

Well its probably because I took it off the dial once too often but my speedo is not working.

I have pulled the pickup out of the gearbox and replaced it but still no go.

I have removed the dash and when I drive the little plastic thing that goes into the back of the dash still spins and also spins under load (me pushing my finger onto it)

I have no idea what is wrong with it can anyone shed some light on this problem. Has anyone else had the same problem?

BACKGROUND

"When I was at the drags the other night I did a burnout and got a lot of axel tramp, it was very violent and shook the entire car. After that the speedo didn't work and my HICAS light came on and I lost my power steering."

Link to comment
https://www.sau.com.au/forums/topic/1048-speedo-no-go-help-please/
Share on other sites

Check if you can pull the tip of the speedo cable (that goes into the instrument cluster) out of the sheathing - that means its broken, and needs to be replaced.

I broke mine once when putting the instruments back in. It work for a while, but eventually gave up.

OK, what I can do is when I remove the speedo console I can also remove the plastic bit inside the end of the sppedo cable. There is a small square plastic bit (like a match stick) and another plastic bit the this fits inside and a spring.....Should all of this be able to come out? If not, what do I need to fix it and where did you get yours from.

Thanks Cam

Originally posted by BOOSTMEISTER

Which bit did you have to replace?

The whole cable.

I tried getting a new inner from the local instrument shop, but they are a sealed unit - only way to replace is with another cable.

Thanks blind_elk I will see how the ereplacement cable goes from Japtaxi, hopefully it will fix the problem.....I imagein it is going to be a nightmare to install...

So, next problem, my HICAS light comes on after about 5 minutes of driving and I loose my power steering, sometimes it happens in the reverse order....I can't find the fuse for HICAS does anyone know where it is? or what could be causing this

Recon it will be related to your non-working speedo...HICAS needs vehicle speed to work, so I'm guessing it throws up an error. I'd sit tight until the speedo is working again, and then if it plays up still, try a diagnostic on the HICAS or visit a friendly Nissan dealer with a Consult unit...(though normally they look like donald duck with dollar signs for eyes when you say the magic words "could you plug your consult unit into my car please?")

Cheers,

GW

replacement cable? I thought you were after the speedo instrument ... doh sorry I'v only got the instrument not the speedo sensor+cable etc.. :D Let me know if you want the speedo instrument as I'm getting lost in all these jargons ... :(

  • 3 months later...

Hi guys,

My speedo just died today. Needle not moving, and the numbers are not running. The revs meter still works though. Then after about 5 mins of driving, the HICAS light turns on and the steering wheel becomes stiffer. Sometimes, steering wheel gets stiff then HICAS light turns on.

You guys reckon it's the same problem mentioned in the previous postings?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Got the motor out and torn down. I'll be dropping off the block Monday. Luckily the scoring on Cyl6 is much less pronounced then the pictures made it out to seem. It can barely be felt. If you pass your finger over it 10x you'll barely notice it. Hopefully by some chance it will only require a honing. I'm not in the mood to buy one size larger pistons or another block. Oddly enough my 6th cylinder with the scoring has extremely clean intake valves compared to my other 5 cylinders. I'm worried the scoring was caused by too much fuel or Water/Methanol washing the cylinder. I'll review some old logs to confirm.  This was also the first time I pull an engine with the transmission still attached. It went much better then expected. I was worried my CD009 wouldn't make it easy due to its sheer size but it was much easier this way. 
    • From the pictures I have when doing the job the flywheel is the same diameter, I don't think they're playing weird tricks like putting weights at the outer diameter to increase flywheel inertia or anything like that. The OEM flywheel is definitely heavier, but it's not a huge difference. Quoted weight savings of the clutch is 2 kg so I can't imagine the flywheel being lighter than ~7 kg. Kind of regret not weighing it before the clutch went into the car but as far as driveability goes I have no complaints.
    • HKS trigger kit should be very easy to integrate with a Link. It's a 36-2 crank trigger. Hard part is finding the motivation to take off the timing belt and everything on the front of the engine to install it. You also need to cut out a hole in the oil pump housing so the sensor can read the trigger wheel. Changing out the cam sensor for a 24 tooth setup is probably good enough but as others have mentioned depending on what underlying assumptions are changed it becomes more of a problem. Reading the crank state off of the cam is an abstraction that works in the general case, but if you have an edge case it makes less and less sense. There is a GTX2860 gen 2 that can take a compact 5 bolt housing so it's direct bolt on but I'm not 100% sure of what's involved. Peak compressor efficiency drops off a bit on these turbos vs -5s, 77% vs 73% but you get way, way wider region of operation. The -5s have a really strange surge line in their compressor map that is all over the place. If you think the hot side on the -5s aren't open enough you can try the Tomei T550B turbos which a local tuner seems to be happy with:
    • i need a complete tail light for my R33 GTR if you have please let me know.
    • I need a great maintenance workshop around Idaho, if you know one please let me know..
×
×
  • Create New...