Jump to content
SAU Community

White Face Dials R32,r32(1)r33(2)r34


Recommended Posts

I used a souldering iron to burn the holes. It's a lot easier.

It would be a lot quicker and nicer if these come precutted.

Overall looks very nice but too much time and effort.

  • Replies 133
  • Created
  • Last Reply

Top Posters In This Topic

hello,

i was wondering on when the next group buy for this is????

what one are you after? I'll sell you mine as I'm selling my car anyhow and I can't be bothered to install them.

I have a white one with green numbers...$100 only if you are keen

what one are you after? I'll sell you mine as I'm selling my car anyhow and I can't be bothered to install them.

I have a white one with green numbers...$100 only if you are keen

pics???

hahahahaha, LIZZZZZZ... why are you selling the car?

Thanks guys for all the feed back! If i get enough interest for them ill do it again.

You can get them pre cut for a bit more money, but its not that hard to cut out dials. lmao

hahahahaha, LIZZZZZZ... why are you selling the car?

Thanks guys for all the feed back! If i get enough interest for them ill do it again.

You can get them pre cut for a bit more money, but its not that hard to cut out dials. lmao

still not 100%on the selling, but time for bigger and better things!

i don't thing they'll fit a 32, but if it's for a 33 pm me your email address and I'll get them too you

hahaha,,, really, will it turn out pink will it.... hmmmm...

and answer is no i am not a girl.

if it wer to turn out pink how would i fix that???

  • 2 weeks later...
hahahahaha, LIZZZZZZ... why are you selling the car?

Thanks guys for all the feed back! If i get enough interest for them ill do it again.

You can get them pre cut for a bit more money, but its not that hard to cut out dials. lmao

Kezza,

lets start up another group buy, I have had a couple of them on otherforums, nothing but positive feedback!!

HOOK IT UP KEZ!!!

i need to get at least 5 people to want to get some b4 i can make an order.. after group buy has been made it only takes a week or two to get them in your hands.

i will start another thread and see how much interest is showen..

thanks,kezza

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The cam I am actually putting in (a few posts up) is actually smaller than my current one. At least duration/overlap wise. All the chop stuff I hear just sounds like an engine running badly, because it is. I then envision driving it around in 1st gear and being massively sad about it bucking to the beat of said chop. There is an idle video of someone with a similar cam floating around the internet, but mine is a custom cam (so is his) so it'll never be the same, plus the fact exhausts are entirely different. What I want to do is put some bullet mufflers/race mufflers in to replace a couple sections straight pipes that currently replace the two extra cats that I don't need. But this is even further down the line!
    • I can tell you now, when the bracket that the little hydraulic ram attaches to snaps, with a subframe, and V8 from an AMG C63 on it, it sounds like someone letting shotgun off right beside you. It leaves your ears ringing, and a huge thankfulness that you never ever put a body part under something heavy that's only supported by a hydraulic lift...
    • Still not a guarantee fix. I used a high quality butyl-mastiq (the black goo that's not really silicone nor polyurethane, same stuff they use from the factory that just spreads out like melty cheese), and I still get lots of water on both sides of the trunk when raining or washing the car. I also suspect the factory spoiler rubber gasket might not be sealing well, so I'm thinking of adding a thin layer of grey silicone around the bolt holes on both sides and see if that's where it also leaks from. The biggest issue is that these cars don't come with a drain hole on each side like other coupes and hatchbacks.
    • I hate it, but maybe he could paint it Monster jam style and call it...godzilla?
    • Would seem to me to be appropriate to go GTR style bar. There are options with and without N1 vent holes, with the GTR lower lip integral (because FG copy). https://justjap.com/search?q=r32 bumper  
×
×
  • Create New...