Jump to content
SAU Community

Recommended Posts

when people are saying 400 k's to a tank, is that 400k's till your fuel light comes on? or 400k's all up?

My fuel light comes on at ~400k's, but there is still 10L left once that happens, so theoretically I could get another 80 or so k's

  • Replies 77
  • Created
  • Last Reply

Top Posters In This Topic

The best way I have found to gauge fuel consumption is, fill the tank full, reset the odo, run it till almost empty (doesn't have to be when the lights on), when refilling next look at how many litres you need to get back to full then check how many ks you've done. That would be the most accurate way to say how many ks you get per litre.

Same here, as Erin, for a few dollars versus pushing the car or walking along the highway. I'll think I'll pay the extra money to be inside cruising along with the A/C on. But I'm lucky to get 300kay/tank

i get about 400 to ~48litres, i've never run it till the light comes on

however since my mercury tune i've been blowing more smoke than a woodstock festival and people who drive behind me complain of stinging eyes

also i get loud backfires from shifting from 1st to 2nd and 2nd to 3rd about half the time

however i just give whoever i just scared a wink like i meant it

I get those figures - seems 350-400ks per tank depending on the amount of city/highway driving. A/F ratos are perfect on the last dyno run i did (only about a month ago).

I think theres a few people on here that pull the 500k figures out of their probervials. Maybe i'm wrong (which i'll readily admit), or maybe their cars run dangerously lean.

I also remember reading an article in HPI where they guy that used to own a soarer that writes in the mag (maybe martin donnon??) was talking about the issue of warming up your car for 5 mins vs just turning the key and driving straight off. Concensus was it was waaaay better for fuel econ to just drive off as the car runs rich as when cold. Hence it was better to go Maybe its relevant in this case- like a temp sensor or even a thermostat problem -car is colder or at least thinks its colder than it is so runs rich for a longer period.

Oh i too get the fuel smell from time to time, no leaks i could find either.

Another point would be the issue of atmo bov vs plumback. Maybe thats causing problems too???

i think we should

i love my car, but its sending me broke

i need some money back

ps i still use the stock bov

my fuel economy seems to have gone out the window with my fmic install

also got a forward facing plenum with ford throttle body at the same time

i think we should

i love my car, but its sending me broke

i need some money back

ps i still use the stock bov

my fuel economy seems to have gone out the window with my fmic install

also got a forward facing plenum with ford throttle body at the same time

lol must be the ford tb then, is it carved from stone :P

Seriously tho i too would welcome any help that can be offered.

Well my a/rs are spot on 12, its almost a straight line. And no joke I got 530kms BEFORE my fuel light came on the other day (90%highway driving) and then it was 610kms before I filled up. Keeping in mind I have a heavier car than most of you, and a smaller engine, which should mean more load and more fuel used.

So, dont mean to be harsh, but for some of you maybe its your driving style?

But I do belive spooks and 53xyn really have a problem.

yup, my afrs are almost spot on 12 as well

doesnt seem to matter if i put around on low boost not boosting

or drive around on high boost not not boosting

perhaps a bit of highway running gets me slighter better returns, but id be lucky to see 400ks from a tank (nearly got 400 driving back from stanthorpe)

also, my charcoal cannister was also unhooked when i had the fmic/plennum done

hence the original post

im going to get my cannister hooked up again anyway, just to see if it makes a diff;

Edited by Spook's_Skyline

My GT-T at the moment is getting just under 400kms per tank (55L) and I think that's pretty bad :( I'm keen on knowing if there is a quick and simple solution to this...

I've noticed that the bigger turbo has helped improve it a bit (especially in the city) due to the lag. Not on boost as often :P

But yes, quick and inexpensive fix - bring it on!

I challenge anyone to take up my offer.

I will come out (you pay for fuel and it must be in brisbane) and if I can't fix the problem or tell you what the problem is...you don't pay me. Anyone getting 400k's or more can bugger off coz you aint got problems cept the right foot.

Edited by 3lit3 32
My GT-T at the moment is getting just under 400kms per tank (55L) and I think that's pretty bad :(  I'm keen on knowing if there is a quick and simple solution to this...

I've noticed that the bigger turbo has helped improve it a bit (especially in the city) due to the lag.  Not on boost as often :P

But yes, quick and inexpensive fix - bring it on!

Stan,

GTTs have a 65L fuel tank, so you should get another 100Ks plus minus. I get close to 600Ks on mine B)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've done a few BMS systems. Code in Canada use to force us to have any safety components outside of the PLC but with a code change back in 2018 I believe it was, we can now use safety PLC's to control everything. Sadly to your point, AB Guardlogix safety instructions for example are only available in ladder.  Machine safety is a very big thing here though, you're constantly forced to migrate to the next best thing by OSHA. I honestly prefer safety plc's, including anything from AB more then I do working with old school safety monitoring relays. PLC is only one portion of it, the rest of the electrical still has to follow to meet SIL (Mechanically linked dual contacts, bla bla)  Now tell me how to feel about safety over comm's (e.g Ethernet/IP CIP) on a unmaintained network haha
    • To your point, boolean logic. We're not only working with bools in ecu's, so it's very limiting. I wanted to setup a low WMI pressure alarm. After 1 second I want WMI line to hit 100PSI, 2 seconds 175PSI, etc. and trigger an alarm if it doesn't meet those thresholds. This would of taken me one very short line of text, but instead I had to bugger around with generic timers, conditions, etc. and so forth.
    • I much prefer that to an actual oil pressure issue, never would of thought it would of been a volt drop issue but SAU brains win again. Guess ill be turning down the oil pressure limit for the track and hunting some grounds. Ill hopefully update this thread with some high oil pressure and solid ecu voltage logs. 
    • You've just discovered a really good reason to tell yourself, yes, I do need to buy an aftermarket ECU. Put the MAF in the bin. Slap in the new ECU and have a think about what turbo sounds you prefer.  Do you want a 90's style BOV wooosh? Do you want a hektik tsututututu?  Mate, can't go wrong. Just gotta get that ECU and the world is your oyster. 
    • Hi. Iam just curisou about this topic. I saw this video. It is about Greddy Type FV2. I know that BoVs are about that sound but how and when to use it? I read some topic here and from what i have understand on stock RB with MAF there will be some "problems" if you use this BoV? It vents the air in to the atmosphere and the MAF on stock car needs this air back in to the intake and not out? Or is it wrong? If so...i saw you can put some adaptor to circule air back...but does that not "loose" that sound? I saw another BoV from Turbosmart and it has two "exhaust" like ports? One is for the stock tubing for letting air back and one is for "sound" and let the air in the atmosphere? Can someone please explain? This is the Greddy one:  And this is the Turbosmart.     THANK YOU!! EDIT: So i read about this topic some more and i if i understand that correctly: That Greddy can function either like BoV or 100% Bypass valve? And that Turbosmart is what they called hybrid so you can adjust what and how many air can be vented out or back in? Is this right? THX!
×
×
  • Create New...