Jump to content
SAU Community

Recommended Posts

hey guys,

I recently noticed right at the front of my gear box where it connects to the engine there is an oil leak near one of the bolts. But its a very slow leak, like after a week in the garage there is a very small patch on the floor. Can someone tell me why it would be leaking there?? Does it need to be tightened more? or too much oil or is something broken? Just wanna know how urgent this will need to be fixed.

I have attached a pic of where it is leaking and circled it. post-23859-1139730510.jpg

Thanks for the help

:P

Link to comment
https://www.sau.com.au/forums/topic/105536-front-of-gear-box-leak/
Share on other sites

It might be the rear main seal, but there appears to be oil staining on the sump further forward in that photo and it might be that the oil is just collecting at the lowest point. Before going to the trouble and expense of removing the gearbox, I suggest you _thoroughly_ degrease the entire area, run the car for a week or so and see if you can confirm where the leak is.

As suggested.. It could just be the sump pan bolts. I've tightened them on another car, and thats been enough to fix the leak. They often work loose over time.

If you're unfortunate, its the rear main seal, which means the whole gearbox (and flywheel) has to be taken off to replace the seal.

It seems to a common problem in older RB engines. My rb20 has had the same problem for quite a while.

defently do a degrease and see exactly where it coming from from.

if you do have to change the seal, the oem ones cost about $80!! i went for an aftermarket which looked exactly the same and cost me $20.

no probs so far (touch wood)

steve

Thanks can you let me know where you got your seal from for 20 bucks?? :P

GRRRRRRR did'nt think of the rear main seal but that's prob what my prob is too. Looking at your pic, it's similar to my issue. It does'nt leak like a sive but when I push the car hard I notice a little puddle and it drips from the lowest point which would be the bell housing of the tranny.

Crap....NOW IM PISSED! :(

I will go through and check that all my bolts are tight but other then the head gasket or rear main seal there really is'nt any other place it could come from. Funny thing is my oil level has'nt really changed at all. :lol:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
×
×
  • Create New...