Jump to content
SAU Community

Recommended Posts

NOW DEFINATELY FOR SALE...

Just wondering if anyone was looking for a project car. I have blown the number 5 cylinder and looking at getting rid of her. has brand new garrett 2530 turboes, hks intercooler, hks turbo back exhaust, hi flow cat. tien suspension... and plenty of extras.

let me know by pm. or 0421544598 if any one has interest in this car. POA

Looking for offers around 12.5k...

Located in perth. has 3 months rego remaining.

Link to comment
https://www.sau.com.au/forums/topic/105633-blown-gtr/
Share on other sites

NOW DEFINATELY FOR SALE...

Just wondering if anyone was looking for a project car. I have blown the number 5 cylinder and looking at getting rid of her. has brand new garrett 2530 turboes, hks intercooler, hks turbo back exhaust, hi flow cat. tien suspension... and plenty of extras.

let me know by pm. or 0421544598 if any one has interest in this car. POA

Looking for offers around 12.5k...

Located in perth. has 3 months rego remaining.

let me know if you want to sell the turbo setup and fuel system.

Link to comment
https://www.sau.com.au/forums/topic/105633-blown-gtr/#findComment-1944840
Share on other sites

wow...

rb30 bottom end = $100

sump adapter = $500

say $2K for fitting it all together with required belts and hoses.

you'd have a newly built 3L gtr for about $15K

oh how I wish this was in a different time in my life..

*SIGH*

If only it were that simple

Flyying

PM'd you yesterday

Link to comment
https://www.sau.com.au/forums/topic/105633-blown-gtr/#findComment-1947938
Share on other sites

Lol, i can field these for him and it's not even my car.

It's an R32 (look under his avatar)

And it will cost around $500 to ship it, although thats a question the buyer should be finding out themselves.

and it's certianly not as simple as an RB30 bottom end, R34 is right..."it never is"

Link to comment
https://www.sau.com.au/forums/topic/105633-blown-gtr/#findComment-1948124
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This is the clearest explanation out of those: Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension. Basically you turn the engine with the tensioner bolt loose, then use the allen key to hold it while you torque it up. And yes after that a good guide is being able to twist it 90o in one of the long free lengths of the belt
    • good choice....I have a set of those and use them all the time including on this job. Plus, no-one wants a damaged nipple
    • Thanks all, went with nismo strengthened belt and all genuine nissan idler and tensioner Question on RB25DET Neo Timing Tensioner: I have a question about the RB25DET Neo timing tensioner. In one of the videos (minute 20 of https://www.youtube.com/watch?v=17y37BB9xnA and minute 27 of https://www.youtube.com/watch?v=Pb99s2E9xUg), the process suggests tightening the tensioner pulley installation bolt to the specified torque initially, and then loosening it slightly to allow the spring to set the correct tension. Is this the correct approach? The R33 workshop manual on page 74 states: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. The way this is written is confusing. Does this mean: Undo the nut, then reduce the tension by turning clockwise? Snug the nut so it stays in position without applying tension to the belt while removing the timing belt? The manual wording makes it sound like the nut will tighten automatically when you turn the tensioner clockwise , which is unclear to me.   Timing Belt Tension Adjustment Process: After loosening the tensioner nut, you turn the engine two full rotations by hand, which should set the correct tension. Once the tension is set, you tighten the bolt to 43 N·m (4.4 kg·m). Before tightening, you need to insert the Allen key into the hexagonal hole to hold the pulley in place while tightening the bolt. In one of the videos, it’s mentioned that you should twist the belt side to side, or turn it slightly to check if the tension is correct. The belt should turn halfway, indicating the right tension. However, I know that twisting or turning the belt is not a good idea. What are your thoughts on this? Finally, how can I ensure the belt isn’t overtightened? I’ve seen many cases where people have overtightened the timing belt.   Manual Excerpts: Page 74: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. Remove the timing belt from each pulley. Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension.
    • Takes a few minutes to malke one. Wood, or steel, or a wrap strap with some strategically placed solids to provide teh drive onto the ribs.
    • I would strongly suggest using the correct tool. They are not expensive and make the job much easier and don't damage the lock ring. Google "fuel tank lock ring removal tool" to see what I'm talking about. 
×
×
  • Create New...