Jump to content
SAU Community

Laurel Wiring Diagram Help!

heyhey!

By heyhey!,
in Four Door Family & Wagoneers

 Share

Recommended Posts

heyhey! Rising Star

heyhey!

Posted
Posted

hi i have purchased a chipped and playd with ecu from an rb20det laurel

the car it was goin into is an rb20det from an r32!!!

this is where i came into problems!!

the pinouts form the ecuare different.....

the car would just turnover but not start

then we noticed that the fuel pump wasnt turning on...thats when we assumed that the pinouts form the ecu must be different fro the lauerel to the r32

can anyone help please??

Link to comment
https://www.sau.com.au/forums/topic/105727-laurel-wiring-diagram-help/
Share on other sites
kudos.motorsports Grand Master

kudos.motorsports

Posted
Posted

I have run a stock R32 ECU and a Power FC in a Cefiro with no problems at all. Therefore I believe it a safe assumption that the pin outs would be no different. Maybe the unit is just faulty.

QUIKBLADE Collaborator

QUIKBLADE

Posted
Posted

Is your problem sorted out?

Hmm, unless it's aftermarket, should you be able to hear the fuel pump running???...

Also, checked battery? Voltage, does all of the instrumentation turn on? maybe not suppying the correct power and pinouts etc? www.rb20det.com has a pinout diagram for an R32... if you don't have on already that is :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R34 Gtt Wheel Offset Advice

      By GTSBoy · Posted

      What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • silviaz
      R34 GTT idle problem

      By silviaz · Posted

      I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • Kinkstaah
      R34 Gtt Wheel Offset Advice

      By Kinkstaah · Posted

      This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • AdiR34
      R34 Gtt Wheel Offset Advice

      By AdiR34 · Posted

      Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...