Jump to content
SAU Community

Recommended Posts

When you consider how easily the RB20 pumps out more power, you shouldn't be put off by the stock figures.

From the replies I've got, it seems that full turbo-back 3" exhaust, pod filter intake and front mount gets you up to around 160rwkw, which is a HUGE improvement on stock.

And when you bear in mind that a stock 32 manages 0-100 in around 7s and the quarter mile in 15s, it's a lot easier to go a lot quicker!

My 2 cents anyway.

the only thing the rb20 is good for is to keep the car on the road until a decent engine can be put in it.

..you see i have a little blackboard in my bedroom...and from time to time people say things that earn themselves a place on that blackboard. Its a short list, but a distinguihsed list.

One day i will get around to paying these people a visit, and if they refuse to rescind their comments about te RB20, even when i have shot them in the boss cags, well im sorry i wont have any choise but to give them the bullet...true story.

Now GTST, the chalk is in my hand, so you really want membership? :P

Throw a 450hp turbo on it, wind in 18-20psi and love the 250rwkw goodness ;)

..you see i have a little blackboard in my bedroom...and from time to time people say things that earn themselves a place on that blackboard.  Its a short list, but a distinguihsed list.

One day i will get around to paying these people a visit, and if they refuse to rescind their comments about te RB20, even when i have shot them in the boss cags, well im sorry i wont have any choise but to give them the bullet...true story.

Now GTST, the chalk is in my hand, so you really want membership?  :D

Throw a 450hp turbo on it, wind in 18-20psi and love the 250rwkw goodness ;)

Count Hardcore...if any interior trim etc is available from CH-01 then let me know :O

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Old Son, did you re-use the Holden ABS in the new shell or try a different module?
    • Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
    • Does anyone know ow what these two plugs are for and if they should be unplugged? Just put the dash back together and can't remember if these were plugged in before or unplugged! (Blue and white plugs) 🤦🏽‍♂️
    • Did some FASTing ...got the impression that the actual part# was a moot point ; seems all of these hardlines for coolant are discontinued/NLA... like, I take it you're after the hardline that bolts onto to the manifold...that's NLA according to amayama & nengun .... ...just to clear up some confusion, they typically mounted the AAC valve to the intake manifold somewhere near a coolant passage, so the body of the valve heats up & holds it open when engine's up to temp - no coolant flows through the valve, it's a mechanical, thermal connection.
×
×
  • Create New...