Jump to content
SAU Community

Recommended Posts

Hey Guys n Girls,

I have a problem with my aircon unit.

When i turn the parkers on the actual lights behind the push buttons will not turn on. (ie. ON button, OFF, TEMP >, TEMP < etc...

Its hassle at night when u can adjust the temp properly wihtout havin an accident.

The digital aircon display works fine and it dims aswell when the prakers go on.

anyone else have / had the same problem ?

possible suggestions please.

Thanks

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

If you search, there's a thread in here about it.

More than likely, your bulbs have blown.

There are two.. one does half a side of buttons. They are a normal globe in a swanky socket that Nissan wants $18 each for. The globes have blue rubber caps on them to make the colour a light blue/green. This also helps kill the globes in hot summer heat. There is a guide here, and on the Silvia forums on how to convert your globe sockets into LED globes, which shouldn't blow.

Thanks for ur help Randy.

I bought the pair of globes at Peps auto parts for $ 3.95

The blue caps were melted onto the old globes...so i just put the new ones in as is.

strange as both bulbs blew out at the sametime ...i thought it was a problem with the unit.

But all is well now....

Oh yea when i finishes puttin everything back together the unit would not turn on. I blew the 10Amp fuse under the dash somehow.

I was bangin my head against the wall i thought i had to strip the dash apart again. But luckily i checked the fuse panel first hehehe.

Thanks

haha mine have never worked lol, thought it was wierd that they didn't have lights in them lol (nearly 5 years haha)

how did you get to the globes? does the face just disconnect?

Jetpilot: no worries mate! I would suspect that one would blow, then the other would go later, then when the car is imported here, they're both dead. =-]

Craved: Just remove the unit like you would the head unit, and then on the back there are two holes on either side. In those holes are the back of the globe-holder. Use a flat-head scewdriver and unscrew! Then pop them out and all you need to do is buy the globes.

I'd suggest getting a 1.2watt bulb instead of 1.4watt if you're not using those rubber caps. It should not be too bright, and shouldn't melt anything if you drop the wattage.

be careful when removing all the plastic components on ur dash as once they crack or break it will never go back in flush and it will rattle.

Take ur time with. It is a lengthy job but its only becoz u have to be careful unclipin the plastic pieces out and puttin them back in.

oh yeah once u put the new globes in...make sure the unit works and lights up before refitting all the stuff.

oh yea some idiot at nissan in the service centre said the unit does not light up...thats why there are indicators on the windscreen button and recirculate button on the aircon unit.

ha...i show him for the benfit of society and job security.

LOL =-D

Nissan Australia mechanics don't really work on many Skylines, since there were only 100 R32's ever delivered to Australia. The rest are all imports and people find GOOD mechanics to work on them.

cheers for the help RANDY and Jetpilot... ive got plenty of experience taing the dash to bits.. mine been customised a fair bit by myself..

must be a fairly comon thing, cos im not sure ive ever seen any light up lol

u know where the clock is on the dash....i cut a round hole just below the clock to the right

and installed a boost gauge...it looks like a factory fitted item.

an a small led red light for when u hit the boost button.

it looks fly

SUPA-FLY? =-p

Nice work though!

Hey Chris, what was the bulb that came out? I haven't replaced mine (only one faulty) yet. When I had the bulbs out I was doing my headunit and didn't have spare bulbs on me at the time.

Could you read off the text off the old bulb or take a photo of it next to a 5c piece? Cheers!

hahaha, just took out the unit .. found the reason my lights have never worked.......

cos there wasn't any :lol: now im gonna have to wait for someone to find out what is the replacement bulb...

basically looks like a push and turn with 2 tabs opposite each other. but the terminals are on the flat surface that it clicks into..

i can take a pic if you still want it.

Nah, i've taken them out before (read my post above).

I just didn't pull the actual BULB out of the holder when I pulled the holders out. I don't want to dismantle the dash, then have to drive down to JayCar or whoever to get the bulbs with the dash apart. (I also CBF putting it back together just to make a trip to get bulbs, and have to pull it apart again) =-]

where can you actually get those bulbs from? actually...where can you get the holders from? Nissan charge heaps for it ($26 for the larger bulb with holder and $20 for the tiny one with holder so i was told). Right now, my whole climate control doesnt light up.

where can you actually get those bulbs from? actually...where can you get the holders from? Nissan charge heaps for it ($26 for the larger bulb with holder and $20 for the tiny one with holder so i was told). Right now, my whole climate control doesnt light up.

I bought them from Dick Smiths. They are called "grain of wheat or rice" from memory.

Have a close look at the holders and you will see that they are just that. They hold these small bulbs in place and make contact.

You will be able to see that the bulb wires are just wrapped around the holder. Just unwrap the old and wrap the new and snip off the excess.

Enjoy!

El Bee

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yuck. But it's kinda the same principle, moving timing around to make car run bad but sound good.... I went for a more spirited tuning drive to iron out a few things. Car no longer stalls, and it loved to dip RPM low when you clutch in. After tuning this (and the 4-5 tables that HPTuners/LS1 OEM ECU wants for idle air correction) it's now behaving somewhat normal. All expected because there's a new TB, new Intake manifold and that new TB which is 102mm vs 78... has an entirely different IAC passage which is smaller because ????? Unfortunately at this point I went to make further fine tuning changes to avoid it flaring up, you know... _tuning_ the HPTuners dongle died. Well to be more accurate - The USB cable died in a fashion that anyone who has ever charged a phone will recognize. After the app demanding I resync it 50 or so times (which all 'succeeded' but all failed) the device does not want to sync and I've logged a ticket with support to see if it's fixable. US Support said it was a 'storage issue' but after removing the SD card inside it and formatting it/fixing it the issue does persist. Unfortunately usually the fix is "Turn in your old dongle and pay $700 for the upgraded one" it's cheaper because I get some free licence credits I unfortunately don't need. However I'm 10 minutes down the road from HP Tuners AUS/VCM so at least I won't need to post it, and logged a new ticket for support over here. Definitely drives different. My SOTP dyno believes it's probably making 310-320kw instead of the 280 before.  It scrambles for traction a little now whereas it previously different. It drives like a bigger cam car up top even though the cam is smaller, likely due to the cam not being advanced 6 degrees. The timing is deliberately low and the fuel is very rich so who knows if this will improve on the dyno. It may, imperceptably. Also funny is removing the pineapples definitely makes the car squat more and axle tramp less. So this behavior of having more top end, squatting more, and scrabbling for traction more makes me think = more power. But I could have just been sitting on the threshold of that kind of behavior before. Time will tell if my butt dyno is calibrated right. I need the exhaust leaks fixed before dyno tune for obvious AFR related reasons - I repositioned the pipes but I'm not confident it's fully sealed even if it is better. At least the car does drive around while I cannot tweak/tune it for now. And I have aircon again. medium success!
    • Don't use that manifold. Please don't use that manifold. Sunk cost fallacy is not worth the later pain. None of these will be relevant to the change that will come from the different turbo and manifold. As in, the effect of the exhaust will be nil, regardless of what else is changed. And all the cam and fuel system stuff is not changing either way, so has no effect. The turbo and manifold (and to a small extent the wastegate)....big change.
    • Just wanted to say thank you for your input   my man (lead mechanic by trade) and I have done a heap of work as you can imagine just to make the hot side work with the dump pipe, stupid massive intake on turbo, trying to get the waste gate on was not fun.  I’m kinda getting to the point where I don’t know if I try and make this work and not throw all this cash and time away or do I scrap the lot and start again? the Apexi I’ve got was tuned for a few slight differences:   Tomei pon cams (mine are stock neo) Turbo smart 38mm external waste gate (mines 45mm replumbed) with stainless screamer pipe  3inch turbo back exhaust with high flow cat Sard 800cc top feed injectors Sard adjustable fuel pressure reg    
    • Out here E90s are the cheapest way into a sporty-ish car because everyone knows just how expensive the repairs can get. 8-10k USD for an automatic 335i. 
×
×
  • Create New...