Jump to content
SAU Community

Recommended Posts

Hi Guys,

My car arrives in march and i want to put some EL dials in for the speedo etc you know the type im talking about. Where is best to buy? Somewhere local or import, and who specifically?

Also i heard doing it can very possibly f**k up your dial and needle calibration... is this a real issue, or more of a beat up? I guess im interested to know what is involved in installing the EL dials and whether i should get it professionally done?

Link to comment
https://www.sau.com.au/forums/topic/105985-el-dials/
Share on other sites

www.modyourcar.com.au sells em for the R33. If you get them fitted professionally you'll have no worries, but that being said, pleanty have fitted them at home and never had any problems.

Steve

Edited by masTers
Link to comment
https://www.sau.com.au/forums/topic/105985-el-dials/#findComment-1956468
Share on other sites

if ur the Impatient type of person,

DIY is a NO NO,

got be gentle with those things,

I screwed up my needle once, cos it was hard to get it off, used a bit of force,

resulted: 2nd Cluster, :D

on a mirage tho,

Link to comment
https://www.sau.com.au/forums/topic/105985-el-dials/#findComment-1957741
Share on other sites

zxfire is right.. i recently bought some cyber stork dials and i was finding it dificult to cut them out so i just pulled my needles off and now they aint gonna ever work again :D so yeh either get buy some good ones and get them installed or dont do it

Link to comment
https://www.sau.com.au/forums/topic/105985-el-dials/#findComment-1958015
Share on other sites

because the EL sheet , on top of the standard dials makes it thicker, and the needle catches....i've heard of people fixing this problem with different techniques, but personally i wouldnt risk breaking my needles etc...

note, havent heard about this happening so much on EL dials, more so on reverse EL as i think they are thicker again.

Link to comment
https://www.sau.com.au/forums/topic/105985-el-dials/#findComment-1958790
Share on other sites

zxfire is right.. i recently bought some cyber stork dials and i was finding it dificult to cut them out so i just pulled my needles off and now they aint gonna ever work again ;) so yeh either get buy some good ones and get them installed or dont do it

I live in Japan, so I could probably pick something up for you. give me a shout back if your interested.

cheers,

Mike

www.j-styleinc.com

mass iv -> you should have ordered the pre-cut meters by Cyberstork, then you wouldn't have had a problem slipping the meters over the needles. B)

Link to comment
https://www.sau.com.au/forums/topic/105985-el-dials/#findComment-1963697
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
    • What are your thoughts on this after having it for a while, worth getting?
    • Downshifts are harder on transmissions than upshifts, the input shaft naturally slows down once disconnected from the engine so the synchros aren't doing all the work. There's no "natural" tendency for an input shaft to increase RPM. Something is not right there, I don't have a great answer on what. You can try a dedicated GL4 75W90, I plan to switch to Motorcraft XT-M5-QS which is supposedly a very good 75W90 for NB Miatas which have a weirdly sensitive transmission from the factory. I would chase down why your clutch is making a hissing noise, that's not normal. It might be no big deal but in the absence of anything else to investigate I would look at that.
×
×
  • Create New...