Jump to content
SAU Community

New Gtr Spotted In Usa

Amaru

By Amaru,
in R35 GTR

 Share

Recommended Posts

Guest Mashrock

Guest Mashrock

Posted
Posted

while i was in the us i saw so many cars driving around nevada, and through death valley that were all stickered up to hide what they were.

i'd say i saw about 10 a day and all very very fast looking cars.

Link to comment
Share on other sites
g35me Mentor

g35me

Posted
Posted (edited)
no the car pictured is the current V35 Skyline (or G35 Infinity in the US) readily available in both Japan and the US

It is a g35 Infinity but it does have fatter rear quarters that a standard g35. And they are now available in Australia now too, because I bought one last week.

Edited by g35me
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      CD009 RB Conversion

      By TurboTapin · Posted

      That's the most absurd thing I've ever heard. I would go cut bellhousing over that monstrosity of a flywheel all day, every day. It puts a lot more mass further from the last main bearing. I've had nothing but problems with Collins in the past and refuse to ever buy their products again. I would not trust anything they tell you. He's playing his salesman card.  I'm currently at 640whp on a mustang dyno (~770bhp) with the intentions of running E85 and a lot more power this upcoming spring. Cheers, 
    • GTSBoy
      PRP RB26 cast block + head prototype running

      By GTSBoy · Posted

      Nah, it's not the reduced knock margin. It is a direct mechanical effect of having to initiate the combustion earlier, while the piston is still rising, which starts to exert combustion pressure on the rising piston earlier, making the rest of the engine work harder to finish driving the piston up to TDC where the combustion pressure stops being a negative and starts being a positive. Your modern engine that only needs ~10° to make MBT doesn't waste the other 10 or so degrees of crank rotation. That's almost all of it. The difference in knock margin might go either way. Remember that modern engines to which you are currently comparing the long tractor engine (the RB) are now running super high compression, direct injection, tricky cam control and maybe even cylinder pressure sensors. You're not comparing apples with other fruit. It's apples and sea weed, or some other evolutionarily primitive vegetation. And remember, squish only really comes into play at the very end of the stroke. It certainly does good things, but it is not the biggest contributor to what's going on. It is quite possibly much less important in 4 valve head than 2 valvers also, because there is so much less squish available to a 4 valve anyway.
    • Dose Pipe Sutututu
      PRP RB26 cast block + head prototype running

      By Dose Pipe Sutututu · Posted

      Food for thought, a longer stroke motor would need less ignition timing vs. a shorter stroke motor requiring more ignition timing.
    • PranK
      Skid pans in/around Sydney?

      By PranK · Posted

      Thanks Duncan, HART is only 10 mins from me (I did my bike license there), it'd be awesome if it ran these types of things.  Sutton Road does look good and they take fewer cars than SMSP which is good.  Surely you have enough land to lay a few million tonnes of concrete and some sprinklers D? 
    • joshuaho96
      PRP RB26 cast block + head prototype running

      By joshuaho96 · Posted

      I thought an engine that needs more ignition timing to make power is going to result in less power due to reduced knock margin? More time for the combustion to propagate -> more time for it to heat up the rest of the mix to detonation.
×
×
  • Create New...