Jump to content
SAU Community

Recommended Posts

  • Replies 71
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

yes i have an aftermarket gtr front bumper and i had to trim it for the piping to fit

and the only hole needs to be cut is under the battery , you can see an imprint of a 3" hole just use that as a guide i cut that hole bit out

and on the other side where it used to have 2 pipes going to the stock intercooler i cut that bit open so its nice and wide and you can manouver the pipes

Link to comment
https://www.sau.com.au/forums/topic/106499-turbo/page/4/#findComment-2289912
Share on other sites

ok the only thing i got now is to do the hole on the side to fit the last pipe. just a question is your intercooler on a angle?? like the top sticks out and at the bottom in comes in. if you know what i mean.

Link to comment
https://www.sau.com.au/forums/topic/106499-turbo/page/4/#findComment-2290084
Share on other sites

yes the intercooler sits on an angle, well mine does anyway and everyones i seen it sits on a angle, like the bottom is closer to the car and the top sits further away

the brackets at the bottom i got with my intercooler kit, they just need to be screwed to the chassis at the bottom..

and at the top i made a plate

both top bolts screw into the fmic and then you get a plate which holds them both togethor, then another one in the middle of the two which can bolt up to a bolt near the bonnet latch you will see it..

Link to comment
https://www.sau.com.au/forums/topic/106499-turbo/page/4/#findComment-2290127
Share on other sites

Hey dude just go to Mettams exhaust and tell them you want a 3inch System from the turbo back (down/dump pipe, high flow cat , the works.) and you can choose a nice cannon style muffler or watever you want on the end. They did a killer job on my R33 for $1100.My car basically went from not much wheel spin in the dry to BLAZING and it doesn't hang down like them ricer jobs and isn't going to atract the cops with excessive decibels.

Link to comment
https://www.sau.com.au/forums/topic/106499-turbo/page/4/#findComment-2296455
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Donut tried them out, they were fine as long as the bolt or nut wasn’t very tight 
    • It is a very complicated plastic tank. Sitting between the rear seats and the rear subframe. Requires a siphon venturi pump in the hat to suck the fuel from the passenger side to the driver side of the tank. The answer is probably prepping the tank very carefully to eliminate all fuel fumes, drilling any cracks to stop propagation, then plastic weld. I don't really see any other solution here. 
    • Does anyone know when your oil drops viscosity, if it is an issue? I imagine with tuned cars they will be overfueling more compared to a stock standard car and will thin out over time. 
    • anyone ever used these ? https://www.ebay.com.au/itm/186214260439?_skw=socket+set&itmmeta=01JEG3TKV388ZXGP8N7CHNCQ45&hash=item2b5b3c1ed7:g:mhAAAOSwwB9lf~Xm&itmprp=enc%3AAQAJAAAAwHoV3kP08IDx%2BKZ9MfhVJKkJwJeiNMm%2FsStacz%2BhjzBowaFnbNCowwe08vVGrW0FbesCs%2Flw%2FQYjDQLjKsuKvgysWT9%2F4b9AZUX3qLP5RDfFhtD8DxufvqBbyZrQAQXuG3h8%2BxxqhWhH8fIfU84eA9W7VIpxDNw9MWj9BdfkkMasYhcqOjTrcKwLyD3ftzZbaZb2Us7%2FFR1Q2kcT68ZYRU77%2F%2BtRr1qBS27BXxh%2FjWBQxhWyUcLlEFIb%2BITZPIKwxQ%3D%3D|tkp%3ABlBMUOy96oP0ZA   I believe the idea being, the rods push back around the shape of whatever nut you put in there. Sounds pretty handy to just need to carry 1x socket in the car for 'most sizes'  but, theory vs reality, anyone tried them?
    • I'm not that familiar with R33 tanks. Plastic? Up behind the rear seat between the towers? Or under the boot floor like a normal car? It's the battery that's up between the towers isn't it? So, plastic tanks. Well, um. The obvious reco is plastic welding, which you'd only look at asking someone who's really good at to contemplate trying. The fuel contamination and grot is probably going to make it quite difficult though. Whether plastic or steel - the end of the crack will want to be drilled before any welding or sealing is done. Otherwise it will just continue to wander along until something bad happens. Steel tank? The obvious answer is drain, wash, purge with inert gas and drill the crack end and weld/braze/silver solder/whatever the guys who do that to fuel tanks recommend. I had a crack/hole/leak in the bottom of a Commodore tank (oe was it my ALFA? - can't remember) that I slammed some gorilla snot onto and it never leaked again. It worked surprisingly well. Or, it's time to fab a new tank.
×
×
  • Create New...