Jump to content
SAU Community

Recommended Posts

Hey guys, got new rims and tyres, so decided to sell my Work VS -KF's off my R33 GTS-t.

(Came off S15 200sx before that)

They are silver with a chrome/polished lip.

Sizes are:

18x8.5 +40 front

18x9.5 +45 rear

The fronts require 5mm spacers each side which are included to prevent the tyres scraping the guards.

All 4 of them will need new rubber as there is peanuts left, hence why so cheap (I dont have time or licence to organise new rubber).

And yes theres gutter rash on them also, any keen buyers can come round for a look.

Located in west side of Melbourne.

PM or email: [email protected]

$1400 obo (+del. if interstate)

SOLD

vskfused18inch6ih.th.jpg

Pic of front.

vskffront5wu.th.jpg

Pic of rear.

vskfrear1fk.th.jpg

Link to comment
https://www.sau.com.au/forums/topic/106941-vic18-work-vs-kf-off-r33-gts-t/
Share on other sites

are there spacers for the rear? I tried a set of a mates 18inch rims on my 33gts-t that were the same widths except ALL the offsets were +45 and the rear rims hit my caliper??

would have only needed 2-3mm slip on spacer to fix....but just asking. Or maybe the spoke shape is different enough to clear the rear calipers?

Yo Abcent, i think the way the spoke design matters.

The spacer is for the front (+45) i tried my new rim on the front the other day (+13 and it needs a 10mm spacer to clear the brakes). Its actually the same rims but different dimensions (Plus VS-KF i know have different spoke designs 2 or 3 i think).

I think these rims need a spacer to clear the struts? :domokun: ? or the guards, i dont think its for the brakes.

Ive actually got them on my car now without the spacer cos unless my lines the only one but the stud threads arent all long and i was worried with the amount of thread left after the spacers put on(Maybe im over cautious).

So i suppose it cant be brakes, but when i turn my wheel a bees d!ck away from full lock, i get scraping, which sounds like the inner guards actually.

[EDIT] Went out to have a look (in the dark though) and the way the spoke design is matters, if my spokes didnt bow out and where more 'flatter' they would hit the brakes or if the rims where +45 offset id say theyd hit the brakes too(they just clear them).

Looked at my new rims and the spoke design is alot more flatter than the ones on my car and both are VS-KF.

Hope that helps.

So if any1 reading this has 2x10mm bolt on spacers lying around PM me i wanna buy em!

RIMS ALSO SOLD PENDING PAYMENT

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It only looks tidy, as most of the stuff that was on the whole back wall, is now in the trailer to go to the tip, or has been shoved in my 2.2x2.4m "Spare parts room", and now I can't get to anything in there Ha ha ha I could definitely do with a bit more space, but I'd just end up with your problems I'm going to enclose the car port beside the garage, and move a lot of stuff into it I think. OR... It will be setup as a fabrication area, and the main garage will have parts storage in it. I'm not sure yet... Need some pictures of that big shed you've got with the bikes and Skyline in
    • No. I think it's gone. 😭 I think you can get body coloured ones on eBay so I think I'll get one of those... Or just hang a red ribbon from the hole and whack a TOW sticker next to it.
    • Can't say I've had a bad experience with one on my car, then again it only gets washed once or twice a year... The wheels on the other hand, get a good spray often due to my shitty dusty pads.
    • @MBS206 thats pretty neat and tidy to me!  I'll get a photo of mine when I'm out there next. It might require multiple photos to understand the scale of the atrocities though... In total I have 4 sheds of varying sizes and layouts. Main shed is 14x8, second shed is 3x8, third shed is 11x2.5, fourth shed is around 6x4.  All are pretty much full.   The main goal of my cleaning tsunami is to make the main shed predominantly car and motorbikes only. Second shed is my metal fab room (2 x bench grinders, drill press, bench belt sander, metal band saw, scrap metal storage and some of my garden tools.  3rd shed is more bigger garden stuff, storage for engine crane, jack stands, concrete grinder, concrete mixer, air compressor lives there, and it now has two 2mx2m pallet racking shelves with itemised boxes holding building stuff, electrical stuff, plumbing stuff, etc, etc.  The 4th shed is Ryobi electric ride on mower, mini boom sprayer, ancient Kubota tractor, more garden stuff!  I have got a lot of shit....  Then there's the pool house (8mx4m) and the pool pump shed (4mx4m).  I built all of the sheds over the 11 years we've been here.  The main shed was a Ranbuild kit, the rest are all custom made to fit the areas available. Building the main shed taught me a LOT as I had no idea about building anything prior to that!  I've still got one more in me. It will be my man cave which I poured the extra concrete for way back when I poured the concrete for the main shed. The idea is the Skyline will be a centre piece of the main cave once (if...) it's finished.  I told my now 14 year old son yesterday that I will 100% drive him to his year 10 formal in 2 years. Still a long way off but at least I now have a date to work towards! 🤣
    • Modern oils are amazing. Add tyres to that as well.
×
×
  • Create New...