Jump to content
SAU Community

How Hard Is It To Drive A Skyline?

blah_blah
 Share

Recommended Posts

tricky_dan Enthusiast

tricky_dan

Posted
Posted

i personally think if a car doesnt have 3 pedals its not worth driving [hard]. so def go a manual if you're in that position. my story is i was in 2 1990 mazda astinas with 92kw fwd for a couple of years (but both were manual), now im in a 1989 manual s13 with a ca18det and ive had no problems adjusting to the whole boost/kick out in the wet thing, just gotta take it easy in the first few months i'd say then you'll get a feel of when to put the power down and when not to..

OH and invest in good tyres! the tyres that were on it were rather worn, when i say that if u ran ur fingers across the rears u could nearly feel some tread... so was heading up 90kmh high way thing (slight up hill) in a heavy downpour, was giving it the smallest amount of throttle possible and going below the speed limit and i felt the tail just start to move to the side.. and i was actively trying to give it next to nothing throttle! got new tyres now, but ive learnt just from that little 'aquaplane/slide thing' to stick with good tread! :D

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Stock rb25det neo questions

      By GTSBoy · Posted

      While it is a very nice idea to put card style AFMs into the charge pipe (post intercooler, obviously), the position of the AFM and the recirc valve relative to each other starts to become something that you really have to consider. The situation: The stock AFM is located upstream the turbo, and the recirc valve return is located between the AFM and the turbo inlet, aimed at the turbo inlet, so that it flows away from and not through the AFM. Thus, once metered air is not metered again, neither flowing forwards, or backwards, when vented out of the charge pipe. When you put the AFM between the turbo outlet and the TB, there is a volume of pressurised charge pipe upstream of the AFM and there is a volume of pressurised pipe downstream of the AFM. When the recirc valve opens and vents the charge pipe, air is going to flow from both ends of the charge pipe towards the recirc valve. If the recirc valve is in the stock location, then the section between it and the TB doesn't really matter here - you're not going to try to put the AFM in that piece of pipe. But the AFM will likely be somewhere between the intercooler and the recirc valve, So the entire charge pipe volume from that position (upstream of the AFM, back through the intercooler, to the turbo outlet) is going to flow through the AFM, get registered as combustion air, cause the ECU to fuel for it, but get dumped out of the recirc valve and you will end up with a typical BOV related rich spike. So ideally you want to put the AFM as close to the TB as possible (so, just upstream of the crossover pipe, assuming that the stock crossover is still in use, or, just before the TB if an FFP is being used) and locate the recirc valve at the turbo outlet. Recirc valve at the turbo outlet is the new normal for things like EFRs anyway. In the even of a recirc valve opening dumping all the air in the charge pipe, pretty much all of it is going to go backwards, from the TB to the recirc valve near the turbo outlet. But only a small portion of it (that between the TB and the AFM) will pass through the AFM, and it will pass through going backwards. The card style AFMs are somewhat more immune to reading flow that passes through them in reverse than older AFMs are, so you should absolutely minimise the rich pulse behaviour associated with the unavoidable outcome of having both a recirc valve and an AFM in the charge pipe.
    • joshuaho96
      Rb25det Belts Change

      By joshuaho96 · Posted

      Yep, in my case as soon as I started hearing weird noises I backed off the tension until it sounded normal again. Delicate balance between enough tension to avoid that cold start slip and too much damaging things.
    • silviaz
      Rb25det Belts Change

      By silviaz · Posted

      nvm this comment
    • silviaz
      Rb25det Belts Change

      By silviaz · Posted

      I'm almost at a point where I feel like changing the alternator. Need to check the stuff you mentioned first though.
    • Wazmond
      Stock rb25det neo questions

      By Wazmond · Posted

      @Dose Pipe Sutututu I read your replies RE: R35 GTR MAFs, any ideal spots to put on? Obviously will need the adapter plate. Will be having a cross over intercooler fitted shortly, would putting it a bit before the TB be okay?
×
×
  • Create New...