Jump to content
SAU Community

Recommended Posts

For sale: 1991 S13 Silvia

Asking Price: $15,500

Kilometer's: 175,000

Transmission: 5 Speed Manual

Engine Type: SR20DET 2.0 RED TOP

Here are all the details:

Engine:

- HKS GT2530 Turbo

- 300zx Z32 80mm AFM

- TRUST plumback B.O.V

- TRUST front mounted intercooler

- Beautiful stainless 3inch piping

- Earls Braided lines

- Yashio Factory radiator, with 1.3bar cap

- GREX remote oil filter

- Stainless oil/air separator with sump return

- Fuel Cut defender

- APEXI 550cc injectors

- Motorsport High Volume Fuel pump

- K & N M's Filter

- TRUST front pipe

- TRUST full exhaust 3.5 inch turbo back

- LUCKY ENTERPRISES remapped computer

- Unknown internal specifications ie.pistons/rods/cams

- Strongly suspect HKS step 1 cams

- Always serviced every 5000kms, only with the best

- Dyno tuned at 200rwkw @ 14psi with sheets

Driveline:

- Custom made 5 puck Carbon composite clutch with sprung centre, 5000kms old

- R200 L.S.D

Suspension:

- KEI OFFICE Fully adjustable coilover assemblies adjustable rebound / height

- Adjustable Camber strut top platforms on front

- TEIN caster rods

- CUSCO strut braces front/rear

Brakes:

- Aftermarket DBA slotted rotors

- 300zx turbo 4 piston Calipers

- Racebrakes custom compound pads all round

- MOTUL 5.1 fluid

Exterior

- Champagne / Silver two tone, original paint in excellent condition

- NISMO bodykit inc: front bar, sideskirts, rear pods, wing

- Freshly tinted 20% on all windows

- Genuine Nissan sunroof, no rust, no leaks

Interior

- Momo race steering wheel

- Pioneer 4350 Head unit

- MTX Thunder 6000 6.5" rear splits

- Infinty Kappa 4x6" in stock position in front

- Fire extinguisher

- HKS automatic turbo timer

- GREDDY electronic guages X 5 (Boost, Oil Temp/Press, Water temp, Exh temp)

- GREDDY Profec E-01 Boost controller

- BRIDE Ergo drivers seat and Bride super low seat rail

- Nismo 260km/h speedo showing 175,000kms

- Digital Climate control

- Full power options

Wheels and Tyres

- AVS Model 6 16 x 8 wheels

- 225/50 R16 all round on AVS rims, new on rear, 40% on front

This car is in extremely good condition inside and out, and mechanically.

Located in sydney.

Pics available by email.

Cheers guys.

Mitch ([email protected])

Car also has a freshly rebuilt gearbox, new brakes all round and a full service.

For pics, see my carsales ad:

http://www.carsales.com.au/pls/carsales/...rch_distance=25

Cheers,

Mitch

Link to comment
https://www.sau.com.au/forums/topic/107214-s13-silvia-200rwkw-15500/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You don’t need to use full throttle all the time to break these blocks, 500kw at the wheels in more then enough to break them even with an occasional squirt. Hell I’ve seen them break under 400kw
    • A work around is to install the R35 card style AFM/MAF on the cold side of the intercooler piping and the BOV on the hot side piping. Works well, also you can combat the revs dropping by adding a bit more ignition timing on the idle ignition timing table to slow the rate of RPM drop.
    • Understood. If you dont have a ridiculous limit,  Tune, T's and P's are in check, and arent bashing it all the time and doing the due deligence for maintenance(inc oil analysis) then its pretty safe. 100% agree, let your right food control it to some extent.
    • So these external kits with the machined block for remote solenoid mount will only work on a NEO head and RB30 or RB26 bottom end   For an R33 head on a 26 bottom end the remote vct kit is to resolve RB26 manifold adaptor plates etc  IF you try to use the remote VCT on an RB30 or RB26 bottom end with an R33 head then  you can starve the cam journal??? I have one of these kits from bits I had years ago before plans changed  I don't understand how that tracks with this video   https://youtu.be/RuPiI22Mplk?feature=shared   This looks like I can run the v termite vct kit to feed the VCT on an R33 head on an RB26 bottom end?!?!?   Lol.... don't v have these problems on RB20s
    • Yeah i know that MAF is no no for this type of BoV. The engine has no BoV and "hose/pipes" ..it was all deleted (or probably it was not even on the engine when it was bought  ) It does that "sutututu" noise which i kinda do not want(atmospheric is better IMO...but standalone ECU)  What are the cons of running without blow off on stock RB25DET NEO. It running 5-7 PSI max (it has boost controller)   EDIT: and can Nistune be "tuned" to know there is no BoV to i dont know "know" and be better for a car? I read so many info about no BoV. One guy saying it is bad and hurting the turbo/engine/car and other that it does not...  
×
×
  • Create New...