Jump to content
SAU Community

Clutch Fork For Rb Gearbox

predator

By predator,
in Wanted to Buy

 Share

Recommended Posts

predator Grand Master

predator

Posted
Posted

After a clutch fork from an RB gearbox. Pretty sure they are all the same.

For those who are not sure whether they have it or not, its basically the lever thing on the gearbox to push the clutch in and out. If you have an old busted gearbox lying around, you might have it spare.

Also after the retaining springs that hold the thrust bearing to the fork, and an old thrust bearing if you have one lying around as well.

SORTED - thanx andrew!

Link to comment
https://www.sau.com.au/forums/topic/107891-clutch-fork-for-rb-gearbox/
Share on other sites
kudos.motorsports Grand Master

kudos.motorsports

Posted
Posted

Gordon I know you haven't asked for it but if you need I have a bearing carrier and fork retaining spring you can have for a four pack of JDs and Lemonade :P I have a feeling I also have a spare fork, but I'll have to look deeper into my box of goodies.

As for the release bearing for the sake of a few bucks buy a new one. IT would be terrible to get the box in and find out that it's on the way out. Not intented to offend Bl4cK32. The bearing shouldn't be any more then $20. If you want to PM your phone number I'll give you a bell tomorrow with a definate price. If you want to carrier I'll organise the bearing ready to collect tomorrow.

Regards,

Andrew

predator Grand Master

predator

Posted
  • Author
Posted

Thanks black32.. have been getting desperate as it was the last thing I need to start putting the new engine in.. but looks like Andrew can come through and he's just up the road :P

Andrew: thanx mate.. PM sent.. :P

burko1 Veteran

burko1

Posted
Posted
After a clutch fork from an RB gearbox. Pretty sure they are all the same.

For those who are not sure whether they have it or not, its basically the lever thing on the gearbox to push the clutch in and out. If you have an old busted gearbox lying around, you might have it spare.

Also after the retaining springs that hold the thrust bearing to the fork, and an old thrust bearing if you have one lying around as well.

Still waiting from another one I've paid for, and some guy has done a runner :) ..

Need ASAP!

my fork decided to crack , i don't recomend getting a second hand fork. I bought a new one from nissan same as a pintara , if i remember correctly it wasn't expensive. Just something to think about.

predator Grand Master

predator

Posted
  • Author
Posted
my fork decided to crack , i don't recomend getting a second hand fork. I bought a new one from nissan same as a pintara , if i remember correctly it wasn't expensive. Just something to think about.

yeah.. i priced one from Nissan $100..

Should be right, but I guess you have a point.. as it'll be me bitching if i have to pull the box out again to fix a snapped fork

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      Possible swap on R34 RB20DE NEO?

      By Kapr · Posted

      Hi. A little bit of an update. It maybe(hope not) looks like i would need a new tranny(it would be "maybe" a cheaper or better option anyway) So i need some info. I know i need a different propshaft(i can make custom one) LSD is not a problem cuz the engine will be still(for now) N/A RB20. So if i buy RB25DET NEO tranny...is there something else i need? I read something about push/pull type but i do not know if i need to "change" something or i can just plug n play onto my engine a go? Thanks for the advice  
    • OakvilleGTR
      Turn signal wiring question

      By OakvilleGTR · Posted

      Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • sonicii
      Lower A arm Skyline v35

      By sonicii · Posted

      The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
×
×
  • Create New...