Jump to content
SAU Community

R32 Gtr High Idle Problems

zinkrb250

By zinkrb250,
in General Maintenance

 Share

Recommended Posts

zinkrb250 Enthusiast

zinkrb250

Posted
Posted

I've searched and read several suggestions on how to fix a high idle problem... check for any vacuum leaks (cracked hoses, etc...), adjust TPS, adjust AAC, so on so on...

I've gone over several vacuum lines so far and haven't found any problem (as of now)... my boost gauge reads just a little below -.5 bar at idle... so i'm not exactly sure it's a vacuum leak.

i've checked the throttle cable and it looks like the throttle bodies are still closed at idle... there's enough slack in the line.

The idle is very steady and sits right around 1600rpm... when i turn my A/C on the idle lowers a few hundred RPM....

Any ideas please help

Cheers

-Andrew

Link to comment
Share on other sites
arbess Experienced

arbess

Posted
Posted

Im not sure if what i saw will help you. I had some similar problem with my gtst. There's a unit called the TPS, that if you play with this it will adjust your revs depending on the angle of your butterfly. I would recommend not to play with this. There is also this little screw at the back of the RB20 that you can play with to adjust your idle. I think that is what your after. I know you have an RB26 I know where the TPS is and i havent moved mine at all. The screw on the other hand that might adjust your idle on the RB26, I have not yet found on mine. I'll try and get back to you where it is, but I cannot guarantee if thats it coz i dont want to play with mine =) Good luck.

Link to comment
Share on other sites
Dash Enthusiast

Dash

Posted
Posted

Had this same problem myself,turned out to be air regulator.

Only thing is you have to remove the intake mani to get to it,if you have a manual you might be able to work out which hoses run to it(bit hard to describe)then block the hoses and check if thats the problem.

Otherwise you'll have to remove the intake.

*note this is what I did to fix it,might not fix yours...

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Stivo
      R32 goes out in right curves

      By Stivo · Posted

      That's true. However, this problem has started since the tuning. First time with the return journey from the tuning. But yes, the pipe was clogged with dirt and rust. That was certainly due to age
    • Dose Pipe Sutututu
      CD009 RB Conversion

      By Dose Pipe Sutututu · Posted

      Great info @tidi0x  Will definitely be handy for others and maybe me if I decide to keep the shit box H pattern.
    • tidi0x
      CD009 RB Conversion

      By tidi0x · Posted

      Bumping this up one last time.... I wanted to follow up on the clutch slave issue. I realized that what the issue comes down to is the pocket is flat milled, and the cylinder does not want rest flat. So in order to mount it correctly you will need to make a spacer for the fingers so the cylinder is floating. I took two plates of aluminum, drilled some holes and was good. I did still need to make the relief cuts in the bell housing, as even with the spacer the bleed section still interferes. The OE bell housing the mounting holes are raised from the housing.       
    • robbo_rb180
      R32 Gtst - Track Car

      By robbo_rb180 · Posted

      If the event in USA goes ahead will be interesting as it seems the rules will get more cars over here. Apparently the track is laguna seca too. Yeah s15, if I get a the lower dash trims, centre console and change front cross member to standard LCA position will fit clubsprint. See how rules are as i would rather do complete widebody than a bolt on flare to run the 295 with proper clearance.
    • 180 wanabe
      370gt Stock Suspension

      By 180 wanabe · Posted

      If the car is legal height I can't see it being an issue. Found a thread on reddit that might offer some insight.   I got a ticket from a copper in QLD for my S15 being too low. They had this wheel thing on a stick that they put under the car and it hit my exhaust. Anyhow went to an exhaust shop to get the exhaust tucked up/hung a little higher and I wound the coilovers up a smidge. Don't think I even had to go back to the police station unlike when I got defected for having a carbon bonnet when I brought the S15 from the ACT to QLD and had to replace it and then rock up at a police station and have a yougish female officer who knew nothing about cars confirm that I had changed bonnets. Should have just painted the carbon bonnet yellow to match the rest of the car lol
×
×
  • Create New...