Jump to content
SAU Community

Sneaking Past The "turbo" Law


Recommended Posts

Xinhua why do you have to come down here every weekend you only need a some sort of mail to go to your bros house and thats about it or if he puts you on the lease it is even better. but you shouldnt have to come down every week end

  • Replies 69
  • Created
  • Last Reply

Top Posters In This Topic

I highly doubt the RTA would hire a private investigator to follow some 17 year old kid around. They have multi million dollar road development projects etc to worry about before they get to you.

Just don't drive like a tool or modify your car to attract attention to yourself and you should be fine.

Lol.. I'm stock and have a gts.. I got pulled over 4 times in one night and followed a few times, mainly cause I was on quiet roads I guess, but still, sometimes you gotta take the quiet roads.. and they are pretty consistent with me.. blah blah where's the turbo, 5 mins of explains it's a gts.. Then them probably double checking everything.. They will... check you.. if they see the red P plates..

So what if i have 18" chromes, exhaust, lowered and a custom plate? whats illegal about that? why do they pull me over..

18" wheels are 2" over the maximum factory supplied wheel diameter.

Exhaust may not meet the DB levels for ADR's, and your catalytic converter could not be functioning properly allowing illegal levels of CO into the atmosphere.

Lowered suspension could make the lowest point of the car below the ADR approved limit, coilover suspension is illegal in most states where not supplied by the manufacturer etc

There's a million and one reasons that could be used to pull you over. Keep in mind they only need to suspect something is amiss on your car to pull you over and question you or inspect your car. The less reasons you give them, the better obviously.

i never get pulled over, and even when i do, they dont bother with anything... my secret...

NO FULLY SICK EXHAUST TIP OR BLOW OFF VALVE that immediately pisses off coppers.

if u get caught driving it, just make up an excuse saying you got no car other then the GTST and u need it to get to work and bacl, otherwise ur gona have to turn to the doll without the vehicle.

Edited by Alien
How many people have been pulled over for a stockie GTS? does it get annoying? and what do you say to the cop?

Cops can't tell that it is a GTS though mate, remember that. Until they physically look under the bonnet. They don't know.

..And even then they still ask "Where is the turbo?" -_-

Stock looking GTS would still probably get you pulled up, especially with cop magnets such as a huge loud exhaust and massive rims.

Obviously the more stock it looks, the better for police sake.

You sure? :cool: I have heard that its defectable

Some cops may defect you for it, but that's mainly because they don't know the law and want to give you a hard time.

The RTA's VSI 06 (guidelines on light vehicle modifications) say that your replacement wheel may not be more than 25mm wider than the largest rim for that vehicle, and the track cannot increase by more than 25mm, while still being classed as a "user certified" mod or in other words something you don't need an engineering certificate for.

It says nothing about the diameter.

I believe that in the RTA's implementation, "widest rim for that vehicle" is the widest rim listed on the tyre placard. Victoria has a similar law, but the "widest stock rim" is based on the chassis (if I remember the article in Motor Magazine's "Hot Tuner" editions correctly). So in NSW a Commodore Executive can have a rim 1" wider than the SS' while still being legal, whereas in Victoria the same car can have a rim 1" wider than a HSV's.

All I remember for certain about that is that Victoria's laws were more generous than NSW's.

Some cops may defect you for it, but that's mainly because they don't know the law and want to give you a hard time.

The RTA's VSI 06 (guidelines on light vehicle modifications) say that your replacement wheel may not be more than 25mm wider than the largest rim for that vehicle, and the track cannot increase by more than 25mm, while still being classed as a "user certified" mod or in other words something you don't need an engineering certificate for.

It says nothing about the diameter.

I believe that in the RTA's implementation, "widest rim for that vehicle" is the widest rim listed on the tyre placard. Victoria has a similar law, but the "widest stock rim" is based on the chassis (if I remember the article in Motor Magazine's "Hot Tuner" editions correctly). So in NSW a Commodore Executive can have a rim 1" wider than the SS' while still being legal, whereas in Victoria the same car can have a rim 1" wider than a HSV's.

All I remember for certain about that is that Victoria's laws were more generous than NSW's.

Thakns for that :geek:

And.. furthermore.. I wonder how many people actually got skylines ( turbos ) when they were 17..

I'd imagine the majority got them around 19-20ish when they had some money etc..

I got my turbo r33 when i was 17 and learnt till i got my P's.....very hard to maintain at that age

So what car are you getting xin?

In other news I pick my car up on Friday after being off the road for.. around 5ish weeks or more I think.. :) Can't wait! I organised a new front bar with my repairer and am looking forward to seeing what it is :mad:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Jap premium will be 100 RON. You should use 98.
    • The exhaust gases are at their highest temperature as they leave the exhaust port and enter the manifold. They cool as they flow through the manifold because they transfer heat to the manifold and the manifold loses heat to the surrounding environment. Thus, inevitably, the exhaust gases are cooler as they enter the turbo compared to when they entered the exhaust manifold. So, yes, the exhaust manifold can easily get as hot as the turbine housing. Having said that, you will generally see the highest temperatures where the exhaust gases have to slow down or they are concentrated into one area - which is usually the collector on the manifold and in the turbine housing, because the gases slam into the metal at those places, increasing the convective heat transfer coefficient and transferring even more heat to the metal than they might just flowing past elsewhere. Exhaust manifold heat shields are a good idea - certainly for the stock manifold they are there from the factory. People seldom have anything like that on a tubular manifold because they are hard to achieve. Some might wrap a tube manifold with fibreglass tape - but this has a reputation of leading to cracked welds. The best case is generally to put ceramic coating onto the manifold to prevent it getting as hot (internal coating) and radiating/convecting heat into the bay (external coating). All the real heat from a turbo comes from the exhaust side. The gases entering are at ~800-900°C and the steel/iron gets nearly that hot. The compressor side is only going to heat the charge air up to <<200°C (typically not much more than 100°C). So that's nothing, by comparison. The compressor is not a significant source of engine bay heat.
    • Late to the party, specifically joined this forum as I just bought one of these and this thread has been a gold mine of info. If the OP is still around, mind if I ask what gas you been putting in yours? Mine has a Japanese sticker in the cap saying premium but it seems to get way worse mileage on premium (95) than 91. I always thought it was meant to be the other way round🤷 I do think Nissans claimed "6l/100km" is a bit fantastical 😂
    • Does exhaust manifold get hot as turno exhuast side? I have a turbo cover to managr heat in the engine bay but  nothing is covering the exhaust manifold before turbo   i know as turbo does compress air, the temp does go up however does that mean exhaust manifold would be as hot?
    • It's excellent but I'm still breaking it in so I'm not 100% sure where it'll end up. I would say it's about 15% heavier than stock and the smoothness of the slip zone is quite progressive but you need to be a little patient compared to stock or it'll bite hard and stall. Stock I got away with absolutely horrid clutch control. Like I said before I couldn't even tell where the clutch would grab when it was stock so releasing way too quickly without enough revs it would just slip and the revs would drop lower than ideal but that would be the end of it. Currently there's a bit of a nasty clutch judder if I don't apply enough revs + find the exact wrong point of the slip point in the clutch pedal but it feels like it's slowly resolving as I drive it more. I would not recommend the competition clutch unless you really need the extra clamp force. I think this clutch combined with the Nismo operating cylinder is going to be exactly what I want. Enough bite that you need to remember the release point to avoid stalling or rough shifts, but progressive enough that it's not hard to drive by any means and not heavy at all. I tried a "super single" clutch on my friend's 997.2 Turbo 6MT and that was absolutely horrid. It runs an electrohydraulic power steering pump for the clutch power boost so there's zero feedback in the clutch pedal and there was a horrific clutch shudder well after break-in due to the lack of marcel springs or hub springs in the friction disk. It felt like the slip zone was the thickness of a single toe twitch as well so it was almost impossible to avoid stalling it unless you gave it a ton of revs and just dumped the clutch instead of trying to be smooth with it. I was terrified of pulling out in front of traffic. I have also tried some kind of "super single" on an EK9 and that makes this twin plate Coppermix look like a stock clutch. Releasing the clutch pedal even slightly too quickly feels like you're getting rear-ended. The pedal is extremely heavy as well and there's no vacuum assist like the GTR.
×
×
  • Create New...