Jump to content
SAU Community

Recommended Posts

Hey everyone im selling my turbo as im gunna upgrade to the SPL model, its brand new never used, has only been mounted on my car, comes with chrome plated front housing and custom billet bellmouth which has also been chromed..

$5000

specs as follows

HKS T51R KAI - 800 PS Output

COMPRESSOR:

-Wheel- 56 Trim - 70.3 Inducer / 94.0 Major

-Housing- 100 Inlet / 80 Outlet

TURBINE:

-Wheel- 76 Trim - 82.0 Major / 71.4 Exducer

-Housing- V-Band inlet / V-Band 115.5 mm outlet - 1.00 A/R

IMG_2090.jpg

Link to comment
https://www.sau.com.au/forums/topic/108645-fs-hks-t51r-kai-ball-bearing/
Share on other sites

hmm, what a nice responisve turbo for a small displacement 6cylinder engine. lol

it looks very nice though

when would i expect boost, aboutt 100rpm after the redline maybe.

what hp is this turbo rated at again?

hmm, what a nice responisve turbo for a small displacement 6cylinder engine. lol

it looks very nice though

when would i expect boost, aboutt 100rpm after the redline maybe.

what hp is this turbo rated at again?

turbo is rated at 800hp, on my engine i was expecting full boost around 4300-4400

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A bit of data is always good, beats the Facebook experts with their opinions I have Bosch 1480cc injectors, often called 1650cc (only when run at 4bar). I run mine at 3bar base so I don't thrash the fuel system. Up top, making 437kW with boost dropping, injector duty is at 69% on E80 (might have had some residual 98RON in there)  
    • I have some downtime due to winter, and just wrapped up converting the car over to flex fuel. We don't get E85 at the pump over here in Canada, but I will be running Ignite E90 Race gas. I'll be mixing it with 99-100 RON pump gas and shoot for 50% ethanol content, up to possibly 85% content if there's any noticeable gains. Here's the question. Most I'll ever want to hit is ~600rwkW. I've currently running 1200cc injectors and want to keep them under 90% duty cycle. As per some online injector calculators, I should be good with 1200's well past 600rwkw on E85. As per other calculators, I'll need 1600-2000cc's. The variety is rather amusing.  With you Australians having E85 at the pump, what realistic duty cycles are you seeing in those kW ranges on E50 & E85 on your injectors? Thanks, 
    • No issues here with my PRP gears in an OEM pump housing. I did confirm all housing clearances were to spec prior though. Cheers. 
    • Thread is a bit old but figured id give my input anyway just incase. Have had lots of water problems in my R32 and was getting sick of wet tools in the boot and water filling up half my taillights. I ended up finding that whenever my car had been repainted they didn't reseal the taillights to the body of the car so water was just flowing straight into the boot, this is amplified by all the water around the bootlid being directed down to the taillights so would get pretty wet whenever I washed the car or it rained. You could probably use silicone to seal them to the body but I think from factory they use a roll of automotive grade butyl rubber. Hopefully this helps you if that ends up being how the water is getting in on your car!
    • Correct And whatever you do, don't use an oil pump gear, especially the one that starts with the same letter as Santa and the last letter ends with the same first letter as Lagoon. Get a proper oil pump, like a Nitto, Tomei, etc. and make sure you invest in a big fk off sump. Won't go into too much detail, but I am sure it caused my previous built motor to go bang.
×
×
  • Create New...