Jump to content
SAU Community

Recommended Posts

Here's just something I've compiled from various threads around the forums of people getting cars serviced .... don't have to get all of it done, but does give you a rundown of what to expect I guess.

Where to go ?

Hills Motorsport in Castle Hill .... As for Mark

Revrite Performance in Silverwater ... Ask for Fred.

What to get done ?

Change Timing Belt

Replace Water Pump

Replace Cam Belt

Replace Thermostat

Gasket Paper for the Thermostat Housing $4 and the goo stuff $5 maybe

Change oil (Royal Purple) and replace oil filter

Change diff oil

Replace Fuel filter (code Z200)

Replace Spark Plugs with NGK BCPR6E (WITHOUT the -11 on the end, meaning a 0.8 mm gap rather than 1.1)

Get injectors cleaned/tested

Get the Block Powerflushed and the Radiator Rodded

Flush your brakes and Mastercyclinder

Handbreak adjustment / calibration

Replace power steering fluid

sair line hoses

radiator and heater hoses

full wheel bearing and bush lube

cv joints re packed

uni joints greesed

door hinges and locks lubed

All Belts and Fluids

Brake Pad Check

Clutch Check

REPLACE WATER PUMP

Replace Air Filter

Fuel Filter

Fuel Pump Pressure check

Fuel Line inspection

Brake LIne inspection

Radiator Flush

Alternator Check

Battery Check

Computer Diagonistic/Adjustment

Link to comment
https://www.sau.com.au/forums/topic/10872-full-service/#findComment-178966
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome Alice......hope you have a bit more luck from here on! What was done in the build?  
    • Hello! I'm new here, I have an R33 GTST that is currently being finished up! Last year was pretty rough, blew two stock turbos so I decided to build the car. Has been down since November, but I get it back next weekend!
    • Hello, I believe my car was imported to America in the 2000s by Kaizo Industries. Would anyone be able to help me find more info on them? I've only found all the basic stuff like that paul walker bnr34, them being shutdown by feds, just stuff like that. Any help would be much appreciated, thanks!
    • I am using Motec M150.  I am not working on the car myself actually.  My workshop is giving all these info, they are quite reputable in the industry and are very familiar with Motec and RBs and have done a few big setups with VCam and single turbo on RBs.  In fact, they built and tuned my engine from day one.  But they are stumped with my engine at the moment and cannot work out how come the compression is so low with the VCam. They told me that they have now swapped in some Kelford cams (without the VCam) and can achieve around 130psi compression and the low end torque is better, but now the engine is doughy as.  It boosts and peaks at more than 1000rpm slower, with twin HKS GTIII RS, it doesn't get full boost until over 5000rpm. I have always thought the VCam was a bit disappointing at the low rpm. To a point I had to ride the clutch a fair bit to get up a small hill from stand still.  That was when I had a clutch.  Now changing to a 8HP, I don't have that luxury and this problem has become a major issue. I am beginning to think the VCam never work since the day it was installed.  Maybe it was just sitting at the most advanced point, that is why it went good at top end but very ordinary at the bottom.  Therefore, with the help of the Holinger 6 speed and paddle shift, as long as it was moving, it drove pretty good.
    • yeah, there's a country that recently started importing Skylines, I blame them.
×
×
  • Create New...