Jump to content
SAU Community

Recommended Posts

Hi Guys,

My wing's brake lights seem to have died. I ripped them out to test various things, and the car's putting 12v up to the lights fine...

Anyway, I'm in the market for a replacement. It's a stock R33 GTS-T type-m wing. Anyone know who's the best person to see about these things? Or perhaps someone has a spare one lying around collecting dust?

Link to comment
https://www.sau.com.au/forums/topic/10907-wing-brake-lights/
Share on other sites

I remember reading about this a longtime ago.

Apparently the lights are all LED's wired in series so they can take the 12v.

The bad thing is if one stuffs up the whole lot won't light up (cause they are wired in series).

Pull the light out of the spoiler and check each LED, when you find which one is stoofed just replace it.

The hard part will be finding a replacement LED the same brightness as the others. Might be easier to replace them all so they all look the same.

J

Link to comment
https://www.sau.com.au/forums/topic/10907-wing-brake-lights/#findComment-178715
Share on other sites

I assume you mean the series 1 spoiler, the curved one that sort of rounds off the back end?

Yes it is a pain to get the lights out of it, the best way is a ratchet with a screwdriver bit, works a treat. Also, I believe the LEDs aren't strictly in series - they are grouped into lots of 5-10 LEDs, and all of the groups are wired in parallel, so that if you blow an LED, only the group that it's in is affected, not the whole array.

Link to comment
https://www.sau.com.au/forums/topic/10907-wing-brake-lights/#findComment-179677
Share on other sites

thats right with what Revhead said, they are in groups, i had a few out on mine when i first got it, it is an aftermarket GTR wing but the principal is the same, it had actually got water inside the casing of the light and corroded part of the circuit board away, re-soldered it back together and put some silicone around it all and it worked a treat, it was just a hassle to take out as the whole wing had to come off.

Link to comment
https://www.sau.com.au/forums/topic/10907-wing-brake-lights/#findComment-179765
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would paint match the whole thing to avoid unwanted attention  I had a similar bonnet, paint matched, on my old R33 GTST, but mine was a fibreglass jobbie made by Blitz in QLD, they work extremely well for radiator efficiency and under bonnet temps
    • Does anyone run this kit with factory plenum? Does the adapter and bosch tb fit under factory strut brace? I wanted to get this setup before going forward facing manifold. Thanks
    • small update time, after always wanting a "cool" looking bonnet for my car and always struggling to find one for the series 2 that i liked and wasn't an insane amount of money. Saw one i liked on RHDjapan from D-speed in Japan the price was very good for a carbon bonnet so good infact i was a little unsure how much i trusted it, decided to bite the bullet and with the help of jesse streeter in not long at all it was at my door. Once it was delivered i ran in from work and quickly unboxed it and to my surprise the quality was actually pretty good i quickly removed the old bonnet and placed on the new one to test it out and even the fitment wasnt too bad at all. Then decided to paint the little grille in the bonnet black to stop it sticking out so much.   I decided to not mess around with the hood latch and just install some aero catch hood pins, having never installed them before did some YouTube university classes and i was good to go. fair to say it is not a fun job at all from making brackets so the pins sit nicely and actually cutting through the bonnet but also being very scared of cutting the holes too big it took wayyyy longer than i would like to admit but finally got it there. Then it was time for a quick test drive to ensure the latches actually worked and thankfully the bonnet looked very stable. I still think paint matching the bonnet and leaving just the part that sticks up as carbon would help make it all look alot neater as im not sure how i feel about all that carbon on a very fridge white car but will leave it as is and see how i feel with time.  
    • I think it's bound to happen, you finally get it all perfect, and bam, something will happen. I took a while to get a Commodore rear quarter repaired where a P Plater clipped it. Two days after getting it back, Sarah wiped it out on a concrete pillar in an underground car park... This is why I take forever to repair them, it stretches how long until it gets bent again... 😛
    • Nah, not really responsible for that little fiasco, but I'm still pissed at myself for writing off my 86, or when I reversed my VX into a pole just before selling it, but, meh, 5hit happens to stuff, all it takes is a slight distraction, and life is full of distractions, and "dooh" moments   
×
×
  • Create New...