Jump to content
SAU Community

Queensland Wasteland


Recommended Posts

  • Replies 28.4k
  • Created
  • Last Reply

Top Posters In This Topic

  • chaos

    4853

  • BelGarion

    4045

  • GTS-t VSPEC

    2546

  • rb25

    2007

Top Posters In This Topic

Guest 87vlt
Originally posted by BelGarion

yer good, yer another ****ing dickhead attacking me again

your right man, i wouldnt have a clue cause my boost guage says 7psi and it doesnt waver till later in the rev range for 9psi, once it hits these marks it doesnt move, mabey i should throw it out

its a ****ing catback u tool, thats it, the boost does not spike, jump or whatever, but then again what the **** would i know, its not like i have a clue what the **** im on about,  there is no ****ing bleed valve, there is no punched out cat or dump pipe or anything, yet im running 14.1, so mabey willowbanks timing gear is ****ed too, got anything else to blame it on?

you ****ing got up people for raggin on your car, your no bloody better yourself you jerk

9 psi is a bit higher than the stock 7 psi ...... I think it has made a difference by putting on a cat back exhaust ..... god damn you take shit to seriously, my point was that was quicker than the supposed 14.5 times nissan quotes. Which I'm happy for you.

Guest Boxhead

i like that last post :)

thats the way we all should care about it..

hahaha, well atleast i do..

umm but seriously guys, even iff for eg, i was to run my car on the 1/4 and i was getting shitty times, then i for some reason started inscreasing without mods...

dont you think maybe ive fine tuned my dragging technique..

and 87vlt - dont whinge about that, coz you know you were annoyed when someone else did it to you

Guest 87vlt
Originally posted by BelGarion

im complaining bout bein single

oh and i ripped into 87vlt for accusing my car of running more boost than the boost guage says

Seriously man stop getting abusive otherwise you'll end up ban like I was. I want to discuss this in a mature manner. Where do I meantion a boost gauge? I said stock boost ..... not what your boost gauge said. You don't need a bleed valve to increase boost by small amounts. Small changes like the strength of the actuator pull, more free flowing exhausts, etc increase the boost, only slight but its still there. This is what I believe has contributed to you getting such a good time with a car thats almost stock car and dude you should care cause its not just a car that gets it to those times.

ill take the catback off, it will still have 7psi below 5000rpm and 9psi above 5000rpm

thats the way r33s are from factory.....

hell if ur that desperate to prove it wrong, ill take my exhaust off and drive it round the block

1. ull see no change in the boost

2. ull pass out from the gasses

3. cops will be called cause of noise

but it will still be 7psi below 5krpm and 9 above it

or you could make up an exhaust that goes from the turbo down to just under the firewall, and drive around on the road like someone i know, who was subsequently caught and fined.

Sounds wicked, turbo spools so loudly, neighbours dont like it so much.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • You know, that is exactly the thing that I was thinking a coupe of hours ago. I even had a plan for a meme, involving one big one, another big one, and the Old El Paso girl saying "¿por que no los dos?"
    • NoS, 2 of the big ones.
    • Oh, that's grim. Something bad has been happening there.
    • Put an endoscope down the hole and saw this. Not quite all around the bore but a good 60% at least. Chin to the chest and towards further disappointments I guess.
    • 2 does "sort of" applies, maybe......but looking at what parts would be needed for the swap to get engineered, registered, and insured, and basically that's everything under the car, the modifications the make it legal would be problematic and horrendously expensive, all for a street car that just cruises around and hits a few twisty roads on the weekends Also, from looking at the NSW rules and Regs, with all modifications that is required just to make the car safe and not twist itself to pieces, and then actually get registered for street use, may still be impossible nowadays As for 1, when you add in a fresh engine, fresh transmission, rear cradle and diff, tailshaft, suspension, brakes, cooling, and all the other fabrication required, your probably looking at up to $100k to do it right, all for a 20 year old MX5 that is over engineered and you would never be able to actually use the power it has on the street, much like your beastie, which I love, but you actually track that thing and can use all of its powers in anger, in a safe environment  Hell, the old Bogan Cruise Ship had more power than I could use on the street, and in hindsight, I went a bit silly on that thing, it didn't really need the 500hp it had for what I actually used the car for, it was fun, but basically unusable on the street if you value your licence  As for cams, yeah, I'll probably book it in for them to get installed and tuned soonish, like next month after MX5 Mania are back at work....... and yes, I've already sent a email to bin the turbo quote and quote instead to install cams and a new Fluidampr balancer that will suit the 2.5 better than the OEM 2.0 balancer that is swapped over for the 2.5 install, as the balancer needs to get pulled to time the cams it's a while your in there sort of thing I did think a bit about flex fuel for a laugh, but being na, and no where really around locally anymore to get E85, I've binned that idea, so no sweet sweet corn smells are set for the car I wish E85 was more of a standard fuel, it's better for the environment, better for tuning, plus that sweet sweet smell we all love As for fitting in the family, that's not needed, as everyone in the family already owns a car that can seat 5 humans comfortably enough, the MX5 is "my toy" As for buying a car that is already built, nah, I would rather pick and choose my parts, I enjoy the process, and in the big picture, the additional cost is well worth the enjoyment, and the occasional frustration, I get out of doing it, albeit with other people spinning the spanners, and me, just paying the invoice 🤣
×
×
  • Create New...