Jump to content
SAU Community

Recommended Posts

Just changing my front shocks - dropped down the new and old to be swapped at the local mechanic. I.e I took the shock dpring assemblies out of car so car sitting here shockless..

I've been waiting for a day or 2 now and was wondering whether I should invest in a spring compressor??

Always been scared of horror stories with these. Are there any that are around $50 that are safe?

Edited by benl1981
Link to comment
https://www.sau.com.au/forums/topic/109585-what-spring-compressors-do-you-use/
Share on other sites

I just went to my local Autobarn and bought whatever they had. Seem to work OK.

Only problem I've ever had is that they tend to twist along the coil - just keep an eye on them and keep them parallel as best you can.

The horror stories would come from not using them - simply undoing the top nut while the spring is under compression, parts shoot off everywhere.

i'm not a fan of the the autobarn etc ones as they twist and somtimes don't grab 100% due to the angle of the taper on some springs. and they're just awkward and take forever. for $175 most industrial tool places will sell you a big ass thing on a stand that locks the whole assembly in clamps and has a hydraulic ram that compresses the spring using a foot pump. very weapons grade and not expensive compared to what a lot of places charge for r and r of springs etc. huge convenience factor if you change springs a bit and if you share the cost with 3 mates it's peanuts.

We have a spring compressor like Scooby described in the workshop, it's a great thing when you need to swap springs many time a day. Or if you are doing Mercedes springs with tonnes of pre-load. It's an overkill for a home garage where you might do one set of springs a year. Particulary on a Skyline that has very little pre-load in comparison.

I have a pair of $25 spring compressors that I bought from SupaCheap a couple of years ago. Carefully used, they have done over 10 sets of Skyline springs without a problem. I just make sure I keep myself out of the firing line.

;) cheers :)

Edited by Sydneykid
Hey guys - thanks.

I just borrowed some from my local mechanic - so heopefully won't injure myself!!

A mate of mine had a set of super cheap spring compressors braeak on him...not a pretty sight. As a general rule, I avoid placing my life in the hands of anything Chinese.

The bottom is free now - I can twist it, however the top seems to still be under a bit of tension. I guess cause I didn't grasp it close enough to the top.

Will this give a bit of impact as I loosen off the remainder of the top bolt..or make it harder to put the compressed spring on the new shock??

http://img93.imageshack.us/my.php?image=img00334iy.jpg

img00354zc.th.jpg

Edited by benl1981

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm seeing torque specs all over the place for the OUTER tie rod, but none for the INNER tie rod, where it connects to the steering rack. Even in videos, people are just tightening em up as much as they can with a wrench and that's it. Anything tightened down without torque makes me nervous. Anyone know what the spec is for it?
    • Hope you had a great time here in our tiny country.   The JDM scene we have here is quite small, it's mostly BMW, Volkswagen with burble tunes haha. But the few JDM cars we do have in the scene are pretty nice. Some of my friends drive cool s14's too. Both built engines, red one makes abt 500, blue one abt 400 i think?
    • Ye good idea , would have never thought of something like that. Might aswell do it to every pulley and the balancer while I’m there 
    • Use an LS1 or similar, via kit like Frenchy's. But.... It's probably not the alternator. It sounds like belt squeal, which would be because the pulleys are glazed. Rub every groove on the pulleys with 120 grit paper. Report back. Oh, and new belts afterwards too. The old new ones will be shitted up already.
    • Hello all I have 2 r34 sedans , one turbo one na, only recently aquired the na 34.  Man what is with these things.... My turbo 34 started sounding like a super charger, it was screaming at anything above 4000rpm , I took the alternator apart and replaced the front bearing which is the only one I think you can access and it did not fix the issue so presumably the bearing in the rear of the alternator is gone. ( diagnosed it was the alternator by taking off the aux belts one by one to figure out which pulley or bearing it was )  My friend gave me one he had lying around, Installed it , it did not squeal for maybe 500kms and now its started to squeal again briefly on startup  Recently got an na r34 and I replaced the timing belt, water pump + all the auxillirary belts. Runs amazing but it suddenly developed the same squeaking problem but significantly worse, Ive had my neighbour come down screaming at me because it was waking her up everytime I moved the car. It takes a good 2 minutes before it quietens down.  Im yet to diagnose where its coming from but im fairly sure its coming from the alternator aswell. My question isnt about how to fix it but rather where can you get a new alternator for an rb25 neo??? Ive searched everywhere but I havent been able to find a direct fit oem type replacement thats not genuine. All the automotive stores sell an oex one - BXA035 - which I picked up for cheap through a friend with staff discount , got it home only to find the connector is completelty different.... As far as im aware bxa035 is for rb20/30's and after a bit of figuring out the bxa035 has an ev14 type connector, which is tiny compared to the rb25 connector. I actually had an ev14 connector lying around which I was considering just replacing the bigger plug with to get the alternator working but the bxa035 is rated for 70amp vs the rb25 alternators are 90amp ( or so ive been told ? ) That paired along with the fact im about to install an amp + sub in the back and I have the stock sized small battery Im not sure itll do the job unless anyone has another opinion?  I know and have seen all the websites selling the ls1 alternator conversion kit but I am not going down that route, nor do I have the money to. Hopefully I can figure out how to get 2 brand new alternators for both cars. I would buy second hand which there seems to be many of but considering how common this seems to be im sure If I installed a second hand one it would start squealing in no time  Or even better if anyone knows how to fix the issue directly with the alternator itself... Any input appreciated Thank you     Link for bxa035 connector picture
×
×
  • Create New...