Jump to content
SAU Community

Recommended Posts

OK guys ive got around 2k to spend on my Skyline

Current engine mods that came with the car are:

3inch Stainless cat back

Pod filter (not heat shield)

BOV

Now this is what im looking at spending my money on. Please give other sugestions.

3'inch twin dump pipe from Bosimporting $450

3' catco cat (just the $280 one) from Bosimporting

Oil catch can $70

Just Jap intercooler and kit $550

Boost gauge $70

This totals around $1400 plus freight.

Other things i was thinking about getting are.

A box for my pod with CAI setup

New fuel pump Bosch 040

Please give ideas

Thanks :)

Link to comment
https://www.sau.com.au/forums/topic/109648-spending-2k-on-basic-mods/
Share on other sites

if you are purcashin from bos (spilt dump pipe)-make sure the sensors on the pipe have been relocated as his first batch had problems.. Not to sure if he has fixed it or not yet..

Or i would purchase CES spilt dump pipe.. Costs a lot more, but probably worth it..

Why do you need a catch can right now?? You arent gettin any detonations right??

So i would finish exhaust off from turbo back, with hiflow cat.. I would also get cam gears(exhaust)..

Front mount, heatsheild for your pod (i might be sellin mine in a months time or so as i wanna get a carbon fibre one lol), then boost controller.. Also a new fuel pump will help!!

get a power fc and tune it..

Then if you got money left over, i would then buy small things, like boost guage etc etc..

thats all you bascailly need to get 200rkw..

Edited by siddr20

Why do you need a catch can right now?? You arent gettin any detonations right??

So i would finish exhaust off from turbo back, with hiflow cat.. I would also get cam gears(exhaust)..

I was going to get a catch can just because there cheap and i beleive it stopes all the crap going into your intake?? There is no detonations.

With the cam gear would i need a after market computer? if not would i need to get the car on the dyno to tune it with the cam gear?? where can i get a cam gear from?

My idea is to get all the mods done up towards getting a Power FC. As i cant afford a Power FC now and tune.

Cheers.

I would buy a stock airbox with a decent panel filter to replace the pod filter. Pod filter is going to cost you performance in terms of day to day driving.

A guy on this forum has made up some boxes that fully seal the pod up, and the air is fed through the stock snorcle. There around $120 each... This is what i was thinking of getting. i guess it would be similar to the stock box and panel filter?

^^ yup thats what i got, from mr_crust.. usin stock snorkle..

you can get cam gears anywhere.. www.nismo.com.au justjap.. any sponsers..

It will be tricky to put in yourself, so when you are ready for powerfc tune, get that mechanic to put it in for you..

However theres a few threads on here about it..

It does gain 10-15kw.. so huge power increase -- i have been told.

if you are purcashin from bos (spilt dump pipe)-make sure the sensors on the pipe have been relocated as his first batch had problems.. Not to sure if he has fixed it or not yet..

Or i would purchase CES spilt dump pipe.. Costs a lot more, but probably worth it..

Why do you need a catch can right now?? You arent gettin any detonations right??

So i would finish exhaust off from turbo back, with hiflow cat.. I would also get cam gears(exhaust)..

Front mount, heatsheild for your pod (i might be sellin mine in a months time or so as i wanna get a carbon fibre one lol), then boost controller.. Also a new fuel pump will help!!

get a power fc and tune it..

Then if you got money left over, i would then buy small things, like boost guage etc etc..

thats all you bascailly need to get 200rkw..

The above makes a lot of sense. The key is in fitting a Power FC, freeing up of exhaust and a suitable boost controller. I'm not sure what type of turbo impeller you have (ceramic or metal),metal is another key in this department as running over 1 bar with ceramic spells trouble. You will need metal impellers if running over 1 bar. Of course a larger intercooler would be nice. But as we know with Skylines they can suck up a lot of moola ($$$)

If you have stock turbo this is all you need!!

Intercooler $550 or go R34 SMIC for under $200 (if plan for bigger things later go the FMIC)

3" Dump/front $250 or pay extra to go split

high flow cat $180 (BATMBL Catco 3")

Boost controller $30 (from forums)

Stock BOV $30 (sell your aftermarket one for $)

Stock Airbox & Snorkel $50

High flow panel (pipercross) $60

Sell your POD

Raise boost to 10-11psi.

Buy PFC $1000

Tune $300-$400 (get the tuner to do one power run on base map to see that is running rich, or check fuel rail pressure to ascertain condition of stock pump, before he gets down the track of tuning) Stock fuel pump should be ok!

You will net about 180+rwkw of very nice responsive power without drawing attention to yourself.

All up about $2-2.5k

Edited by benl1981

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After 23 years of owning a Skyline, finally had the latch go.  Followed this guide,  works like a dream again. Great Guide 👍
    • Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • Have you looked at the workshop manual?
    • Hmm. I've gotten pretty good outcomes from talking to them about things that I've had go wrong or ideas for improvement. Have had a lot to say about the R32 FUCAs, and they have sent out some replacement parts for those, gratis, on a couple of occasions. Mind you, I have bought a couple hundreds of $ of replacement rod ends for them too!
×
×
  • Create New...