Jump to content
SAU Community

Recommended Posts

That I bought from someone with the assurance that it was hiflowed, and just needed new seals. For the price I didn't really care whether it was hiflowed or not, basically just wanting to learn more about turbos.

ANYWAY, cutting a long story short, while knocking off the turbine housing, I broke the shaft, which I'm 99% sure is ceramic anyway (given how easily it snapped, it's colouration and the surface finish). Is there even such a thing as a hiflow that only replaces the compressor wheel?

So my question is, how can I remove the compressor wheel? The most obvious option to me is using an easy out tapped into the turbine end of the shaft, but I'm not sure how much the ceramic would let me do that. anyone know of any other possibilities?

cheers

Jeremy

Edited by jezzerrr

Since the turbines dead making the shaft useless all thats any good is the bearing housing and compressor wheel - if its aluminium . You could break up the remains of the turbine wheel and tack weld a cross piece to the flat bit so that it can be held and the compressor nut removed .

Or you could very carefully grind the nut and shaft away till the compressor can be removed though the burr may be a problem .

Its ages since I looked at a Hitachi with a damaged turbine . If enough of the steel section of the shaft protrudes from the bearing housing you may be able to slot it with a saw and use a large plain blade screwdriver in a vise to hold it still while you undo the nut . Two pairs of hands helps .

I'll have another look, I may also be able to get an easy out into the compressor end of the shaft, and undo the nut that way. if that fails, I'll try the other options.

cheers

Edited by jezzerrr
I'll have another look, I may also be able to get an easy out into the compressor end of the shaft, and undo the nut that way. if that fails, I'll try the other options.

cheers

Dont know of anybody who hi-flows and retains the ceramic rear wheel. Defeats the purpose.

GCG highflow consists of new cartridge and wheels (obviously) uses existing housings but profiles comp cover to suit larger compressor wheel.

yeah that's what I thought. may as well replace the biggest achilles heel while you're in there. I'm still not sure about this compressor wheel though... It's got two paint pen marks on it, one blue, one yellow (from memory), and it also has an N and an 8 cast into the wheel, on opposite sides of the wheel at the blade tip end of the wheel. The wheel also has a few chunks of alloy missing at the inlet end, I'm guessing from the balancing process as there are no scores or marks whatsoever to indicate that they went through the turbo. Given the 8 cast into the bearing housing, I'm fairly sure that it's not a hiflow wheel, but I could be wrong. The pen marks are the wierd thing for me.

Since the turbines dead making the shaft useless all thats any good is the bearing housing and compressor wheel ...

Sell it to someone whos been picking bits of ceramic out of their cat and cursing their bleed valve?

Sell it to someone whos been picking bits of ceramic out of their cat and cursing their bleed valve?

You will need the turbo for the upgrade, dont throw it away or anything, they use your housings.

If you dont want it ill buy it.

Edited by Bezerkly
yeah that's what I thought. may as well replace the biggest achilles heel while you're in there. I'm still not sure about this compressor wheel though... It's got two paint pen marks on it, one blue, one yellow (from memory), and it also has an N and an 8 cast into the wheel, on opposite sides of the wheel at the blade tip end of the wheel. The wheel also has a few chunks of alloy missing at the inlet end, I'm guessing from the balancing process as there are no scores or marks whatsoever to indicate that they went through the turbo. Given the 8 cast into the bearing housing, I'm fairly sure that it's not a hiflow wheel, but I could be wrong. The pen marks are the wierd thing for me.

If its damaged, it will have to be replaced anyway.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...