Jump to content
SAU Community

Free Exhaust Db Testing

WiZardOz

By WiZardOz,
in Queensland

 Share

Recommended Posts

WiZardOz Collaborator

WiZardOz

Posted
Posted (edited)

NOISE TESTING

When - 18th March ( Tomorrow )

Time - 10am start

Where - Mt Cotton Driver Training Centre

Cost - !! FREE !!

Mt Cotton have come to the party :) as it's not something they normally do they have decided to give us 1 hour FREE so they can 'see how it goes' and decide if it's a service they should be providing (at a cost in future) - how many cars get tested will come down to how organised we are

Anybody planning on attending SkidPan/LVMA events in the future here is your oppurtunity to know where you stand in regards to the noise restrictions placed on cars participating.. 5 spots up for grabs

1. WiZardOZ

2. RhinoRebel

3. R33S2

4. jlnewton

5. SMR33

6. pear

7. lbfalcon

8. ed G

9. chaos

10.

Edited by WiZardOz
Link to comment
https://www.sau.com.au/forums/topic/109976-free-exhaust-db-testing/
Share on other sites
WiZardOz Collaborator

WiZardOz

Posted
  • Author
Posted
will a fine turnup in the mail if we dont pass

No there will be NO come backs from this ... last SkidPan event there was a number of cars that "failed" but there was no problems .. just meant that those cars couldn't use the facility

Mt Cotton are only concerned with meeting the EPA obligations for the facility

WiZardOz Collaborator

WiZardOz

Posted
  • Author
Posted
Are they now restricting cars into the premise that they suspect are above Db limit?

If they find your car is over the limit will they note it, and restrict you next time you wish to use there facilities?

They are now enforcing a 90Db limit on cars participating in events at the complex. - Council / EPA requirements. Last time we had a members only SkidPAn event all cars got tested before being allowed on the SkidPan

As a side note I also noticed on the Dutton Rally site that all participating vehicles are required to meet a 90dB level (ie .. the legal limit)

R33S2 Grand Master

R33S2

Posted
Posted

Nah its just for competitors on the facility and they dont care how it got there or where its going its just for the competitor cars on their grounds and as an offer for SAU Qld to check before we actually do it and dont get knocked back after we've paid in advance.

BelGarion Grand Master

BelGarion

Posted
Posted

seriously ed, easy fix, get a piece of 2mm steel sheet metal. Cut it into the shape of a 2 bolt exhaust flange, drill 20 or so holes in it (less depending on how quiet and how much power you want to loose) and then slide it up between your catback and cant converter flanges.

oh, who won overall?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Rear subframe stay bracket bolt removal issues

      By GTSBoy · Posted

      Grind them off, drill them out. Repair any rust on the other side. Start again from scratch.
    • Iron Mike
      R34 GTR parts garage clean out

      By Iron Mike · Posted

      Big R34 GTR parts cleanout. I have a lot of stuff collected over the last 14 years and my missus is giving me hard time. Make my life easy.   Nismo GT carbon fibre diffuser fins (discontinued)  NEW  $2900 Garage Defend Stingray canards carbon fibre  NEW  $1300  Top Secret G Force carbon fibre front diffuser  NEW  $2000  Haltech Elite 2500  NEW  $2500  Haltech Platinum Pro R34 GTR   USED  $1400  Apex’I power FC D'jetro + hand controller R34 GTR   USED  $1400  Nissan OEM BNR34 ECU  USED   $1000  HKS EVC 6  USED  $600  Blitz dual SBC ID boost controller.  USED  $350  TRE 255 LPH Fuel pump  NEW  $100  Fujitsubo  Super Ti exhaust  USED  $2700  Tomei Expreme Ti exhaust  USED  $2000  Trust stainless steel front pipe  USED  $1000  Apex’I super suction kit  USED $400  BC BR coilovers  USED  $600  Hardrace front upper camber kit. USED  $300  Garret 2860-5 turbos –  one good, one needs reco USED  $1000  Nissan OEM Toshiba MFD Screen replacement  NEW  $450  Nissan OEM BNR34 Series II front passenger seat  USED (mint) $5000   Nissan OEM BNR34 front bar in TV2  USED  $1000  Nissan OEM BNR34 front lower air spoiler  USED  $900  Nissan OEM BNR34 front lower air spoiler (painted)  USED  $900  Nismo front indicator (clear) USED  $80 Nissan OEM BNR34 radiator  USED $500  Nissan OEM BNR34 turbos  USED  $500  Nissan OEM BNR34 intercooler USED  $800  Nissan OEM BNR34 front swaybar   USED  $500  Nissan OEM BNR34 intake pipes   USED  $400    Also have a square set of uber rare Volk CE28n in 19*10 +22. Not really keen to sell these but make a high enough offer and maybe I will. If you don't know how much these usually sell for don't bother.   PM for pics.  Pickup Chadstone VIC or postage at buyer's expense.
    • waxracing
      Power steering pump r32

      By waxracing · Posted

      Thanks Mate, I did know you could do that but i know there is a pump out there that you can bolt on and it all lines up. I was told about it and then forgot the model, I figure if i am pulling it apart i will just put a new one on 
    • TurboTapin
      Power steering pump r32

      By TurboTapin · Posted

      You can also remove the veins from the HICAS portion of your existing pump. 
    • DatsunBanana
      Rear subframe stay bracket bolt removal issues

      By DatsunBanana · Posted

      Trying to swap the rear subframe on my R34 and can't remove the L-shaped stay brackets between the front subframe mounts and the sill/chassis. I'm in the UK so rust is a problem. I've used loads of WD40 and then Tunap 103 for days beforehand. I backed off the bolts forward a bit, backward a bit repeatedly for ages to try and avoid snapping. They have all moved a few full turns. The one I've spent most time on has come loose and I can turn with fingers, and it will pull down and push up 2-3mm. But it won't come out. I can tighten it back up and loosen it off again repeatedly but it still won't come out. I assumed there's a captive nut inside but if that's broken loose then I can't understand why I can always tighten the bolt back up - I'd expect it to just spin both ways. Any ideas what's happening here? I can't visualise what's inside there to cause this.
×
×
  • Create New...