Jump to content
SAU Community

17" R34 Stock Wheels + Good Tyres


Recommended Posts

Hey all have a set of R34 17" stock rims and tyres for sale.

Tyres are roadworthy and are goodyear ducaro revspec 225 45 17. Handle very well in wet & dry conditions.

One rim has a slight scuff on one of the spokes, otherwise very good confition.

Selling as is. Photos below;

post-26791-1142598045.jpg

Sample pick above.

Actual Pics Below.

post-26791-1142929176.jpg

scuff mark on outer spoke above.

post-26791-1142929402.jpgpost-26791-1142929421.jpgpost-26791-1142929436.jpg

Tread wear of all tyres shown above

Looking for $800+

Regards,

Paul.

Edited by paulsid
Link to comment
Share on other sites

Hey all have a set of R34 17" stock rims and tyres for sale.

Tyres are roadworthy and either dunlop or goodyear. Either way they handle very well in wet & dry conditions.

One rim has a slight scuff on one of the spokes, otherwise very good confition.

Selling as is. Will take some photos.

post-26791-1142598045.jpg

Sample pick attached..

Looking for $800+

Regards,

Paul.

ill give u $500

Link to comment
Share on other sites

Hey..

As many nissan wheels are interchangable, given that these wheels and tyres are factory spec. I doubt very much that you will have any issues fitting on later model skylines.

For your reference specs are;

Wheels f/r 17x7.5JJ

Tyres f/r 225/45ZR17

I have no issue with sending wheels interstate dependant on final arrangement.

Cheers,

Paul.

Link to comment
Share on other sites

Note: R34 GTT Stock Wheels will fit all skylines.

But R33 GTS & maybe even the R32 GTS stock Wheels will not fit the Front of the R34 GTT cause no clearance of brake caliper.

Cheers...

Yes - the R34 does have chunky front brake calipers!! and I have tested them.. pulls up very fast!

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Pretty simple question. I was about to put the transmission back in and thought I pretty much had it lined up when I noticed it seems like the pressure plate isn't flat. I was pretty careful when undoing the bolts both during initial disassembly for cleaning and when torquing them up for installation so this is pretty discouraging. I'm not sure if I accidentally bumped the pressure plate with the input shaft and bent it somehow or if it just showed up this way. Is it possible that there's just something obvious I'm not doing correctly? I'm pretty sure I was extremely careful to make sure the friction discs were seated correctly in the hub, everything lined up, flywheel torqued according to sequence, the little springs all sitting correctly in their seats, etc.  What's the play here? Do I jump straight to a new pressure plate?
    • OK. I can see that being the case. But if you live in the land of "only switching between 4.08, 4.11, 4.36" like most Skyliners, then you never encounter it. Now I perhaps understand why the crownwheel is thicker on some of the smaller numerical ratio diffs. The two stubs being the same (unequal) lengths and just swapped side to side between the different cases is a new one to me. I'm hating Nissan R200s more than ever now.
    • Reason I say this is I have seen broken ones, in drift, drag and even behind a stock Z. I do appreciate most of the time its the synchro's that go.   Trouble with quoting HP is it doesn't really say how strong the box is.  I've not seen many CD00X box's make it past a mid 9(150mph) I have seen about a stock R33 RB25 box's run a 9 too, they all go boom at some point though.   Another clue is they make gearsets for CD00X box's too, wouldn't be a market if they didn't break or have a limit people are going past.   I totally agree it is a strong box, just have to weigh up the true total cost of the conversion vs rebuilding with a good gearset. 
    • What makes you say CD009 boxes are not as strong as you would think? I've always been told the last revision (CD00A) is good for 1000whp and I have no issue's believing it when comparing one side by side with an RB25 box. Makes them look tiny. 
    • I picked up an open Center with shafts. I was told the Open shafts will fit a mechanical LSD and looking at them. I think they will work. Will update 
×
×
  • Create New...