Jump to content
SAU Community

Justjap D2 Coilovers

sanger
 Share

Recommended Posts

sanger Community Regular

sanger

Posted
Posted

Hey guys,

Just wondering does anyone have a set of those d2 coilovers from just jap in their car? Anyone got any thoughts on them. obviously for the price they will not be the best coil overs around but im just curious are the spring rates etc ok for street, Without having to install new kidney's i mean...... :(

Link to comment
https://www.sau.com.au/forums/topic/110077-justjap-d2-coilovers/
Share on other sites
sanger Community Regular

sanger

Posted
  • Author
Posted
Have you seen their new G4 coilovers for $1399? Similar to D2 with different rate springs available.

Check the business traders section

Thanks blitz will have to check em out.

Hey scary32 you in sydney????? going to any of the track days or cruises soon? It would be cool to check a set out on a car before i bought anything. Dont have the dollars yet anyway but always researching the next mod!!!! :(

Adrian Knack Contributor

Adrian Knack

Posted
Posted (edited)

I've got a set in my Silvia and they are so much better than stock suspension. Car sits nice and flat through the corners and feels sharper. For me it was a good choice.

The D2s come in different sprin rates and different oil/gas and valving setups for Street, Track, Drift and Rally... I went with the streets and went 2kg lighter than the "standard" because NQ roads are not the best in some places... You would probably go harder springs and the correct type if you were going to use them for drift/circuit or rally (probably not in an skylines...).

Have a chat to your provider and they will get you the right stuff. Or have a look at the D2 website for all the details so you know what is available and what they say is standard for your car.

Cheers

Adrian

PS. Mine took about 500km to run in nicely. Before that they felt very hard and bouncy. Afterwards they were/are great.

Edited by Adrian Knack
Wink Grand Master

Wink

Posted
Posted

Are D2 a well established brand?

They sponsor the CLK-GTR LM race car:

Mercedes%20CLK-GTR.jpg

From this sponsorship I always thought they were some high end Euro brand but these cheap coilovers seem to belie this theory.

NateR31 Grand Master

NateR31

Posted
Posted

coilovers eliminate some body body roll, camber/damper/highett, none of which kingsprings on a stock strut can do.

when i got some it got rid of alomost %50 of body roll. but if you arent going to the track or anything like that i dont see the point why you need them other than to say "hey look i have coilovers"

sanger Community Regular

sanger

Posted
  • Author
Posted

Thanks for the feedback guys... I will mainly be using them for street with a couple of track days a year thrown in for good measure. Anyone checked out the g4s?????? They look ok to but but would be cool if anyone has any in a car!!!!

Beer Baron Grand Master

Beer Baron

Posted
Posted
Are D2 a well established brand?

They sponsor the CLK-GTR LM race car:

Mercedes%20CLK-GTR.jpg

From this sponsorship I always thought they were some high end Euro brand but these cheap coilovers seem to belie this theory.

3 things:

1. that photo is around 10 years old.

2. it's not the same D2.

3. from memory D2 Privat is a german phone company... i think.

:)

Sydneykid Grand Master

Sydneykid

Posted
Posted

Some clarification;

1 Body roll should be controlled with the anti roll (stabiliser) bars, springs are there to hold the car up and absorb bumps. If you have a spring rate high enough to limit the roll substantially, it will be too high to absorb the bumps.

2. On a double wishbone car (like R32/33/34 Skylines) camber is adjusted via the control arms, not the shock/spring unit.

3. You can buy the Kings/Whiteline etc springs in the correct height

4. The Bilstein shocks in the Group Buy come with additional circlip grooves so that you can further fine tune the height.

5. R32/33/34 Skylines come with coil overs standard (the coil spring is located around the shock absorber, hence coil over)

Check out the Group Buy thread for more details, and some feedback from the 50 or so guys that have bought kits.

:happy: cheers :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I mean I can be OCD'y but this is really over the top. At that point why not just run a full wideband fuel controller? Especially if you run 3 widebands. The system works pretty well, which is trimming low load stuff to be within a few percent of the base map. Pre-engine _change_ the base map was only 1-2% off, depending on ambient temp, elevation, etc. Under load the LS is really very straightforward to tune, enough that a wideband closed loop would be overkill. If I really cared (and I hope I don't) I can always just go back to the MAF system the car actually came with. Which does all those nice calculations for me (temp, altitude, etc), now that you can buy 102mm MAF's that do not cause restrictions.
    • Pac
      Who has a Infiniti Q60, Q50 (V37)?

      By Pac · Posted

      Good afternoon Team , just a quick update on performance mods  Current Mods list (Installed) HKS - Power Editor (Came with the car) looks to be some kind of boost controller RV37 Skyline 400R (SKYLINE) | FUJITSUBO  - Cat Back  RV37 Skyline 400R (SKYLINE) | FUJITSUBO  - Front Pipe AMS  - INFINITI Q50/Q60 RED ALPHA COLD AIR INTAKE KIT AMS  - Performance Heat Exchanger Intercooler Not Yet AMS Alpha Performance Full Race Down Pipes  - to be installed in May 
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I'd be installing 2x widebands and using the NB simulation outputs to the ECU.
    • GTSBoy
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By GTSBoy · Posted

      Nah, it's different across different engines and as the years went on. R32 era RB20, and hence also RB26, the TPS SWITCH is the idle command. The variable resistor is only for the TCU, as you say. On R33 era RB25 and onwards (but probably not RB26, as they still used the same basic ECU from the R32 era), the idle command is a voltage output of close to 0.45V from the variable resistor.
    • dbm7
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By dbm7 · Posted

      It's actually one of the worst bits of Nissan nomenclature (also compounded by wiring diagrams when the TCU is incorporated in ECU, or, ECU has a passthru to a standalone TCU).... the gripe ~ they call it the TPS, but with an A/T it's actually a combined unit ...TPS (throttle position switch) + TPS (throttle position sensor).... ..by the looks of it (and considering car is A/T) you have this unit... https://www.amayama.com/en/part/nissan/2262002u11 The connector on the flying lead coming out of the unit, is the TPS (throttle position sensor) ...only the TCU reads this. The connector on the unit body, is the TPS (throttle position switch) ...ECU reads this. It has 3 possible values -- throttle closed (idle control contact), open (both contacts open, ECU controls engine...'run' mode), and WOT (full throttle contact closed, ECU changes mapping). When the throttle is closed (idle control contact), this activates what the patent describes as the 'anti stall system' ~ this has the ECU keep the engine at idling speed, regardless of additional load/variances (alternator load mostly, along with engine temp), and drives the IACV solenoid with PWM signal to adjust the idle air admittance to do this. This is actually a specific ECCS software mode, that only gets utilized when the idle control contact is closed. When you rotate the TPS unit as shown, you're opening the idle control contact, which puts ECCS into 'run' mode (no idle control), which obviously is a non-sequitur without the engine started/running ; if the buzzing is coming from the IACV solenoid, then likely ECCS is freaking out, and trying to raise engine rpm 'any way it can'...so it's likely pulling the valve wide open....this is prolly what's going on there. The signal from the connector on the flying lead coming out of the unit (for the TCU), should be around 0.4volts with the throttle closed (idle position) ~ although this does effect low throttle shift points if set wrong, the primary purpose here is to tell TCU engine is at idle (no throttle demand), and in response lower the A/T line pressure ... this is often described as how much 'creep' you get with shifter in D at idle. The way the TPS unit is setup (physically), ensures the idle control contact closes with a high margin on the TPSensor signal wire, so you can rotate the unit on the adjustment slots, to achieve 0.4v whilst knowing the idle control contact is definitely closed. The IACV solenoid is powered by battery voltage via a fuse, and ground switched (PWM) by the ECU. When I check them, I typically remove the harness plug, feed the solenoid battery voltage and switch it to ground via a 5watt bulb test probe ; thing should click wide open, and idle rpm should increase... ...that said though, if it starts & idles with the TPS unit disconnected, and it still stalls when it gets up to operating temperature, it won't be the IACV because it's unused, which would infer something else is winking out...  
×
×
  • Create New...