Jump to content
SAU Community

Skyline Crash In Merrylands

raz0r$harP.UK

By raz0r$harP.UK,
in New South Wales

 Share

Recommended Posts

Merli Grand Master

Merli

Posted
Posted

From the thread in General Automotive Discussion:

http://www.skylinesaustralia.com/forums/in...howtopic=110099

There was an accident involving a R33 GTST at 2am Friday night on Chetwyn Rd,Merrylands. There was four people in the car including a three year old boy and his mother. The boy and his mother survived, sadly the driver and front seat passenger did not.

The accident was the next street down from my home address. I noticed it after leaving home this morning. The car has left a straight section of road, hit a tree with enough force to throw the engine into the park.

The people live 100mtr's up the road and I see them all the time and the car all the time.

There is no doubt they were speeding but there are some factors to consider and take on board. Firstly he has been driving around with the emergency spare on the drivers rear corner for the last 3 weeks. I mentioned he should change it asap as there is a real danger of it blowing out. Another factor is too hard suspension and 20 inch wheels which may have lifted the passengers front wheel causing loss of control.

I believe this is what happened, losing complete control and carrering into a tree.

People have been using this road for increasingly over the last few years to lay some power down. Only a week ago I knew something was going to happen sooner than later and it has. The thing is I expected it to be a few people with high powered V8's which have been ruteenly waking everyone up lately. Mabey a person being ran over or a crash, which has happened in the area numerous times resulting in death.

Chetwyn rd really needs a camera there to slow people down before the inevitable happens which now has.

If you want to go quick, go somewhere where there is an exit plan not high density suburbs. Track days, supersprints,N.T., etc or you may pay the price of life and your family and friends will suffer till their time comes.

This guy was my neighbour. I saw him a few times a week driving past and stopped and chatted regulary. This includes the other people in the car. He only had the car a 2 months I think and that was it.

I send my condolences and sympathy to all their family and friends for their loss.

Steve

"Questionable" driving with your 3 year old child and wife in the car, whilst sporting a space saver.

Condolences to family and friends.

Charles_Darwin.jpg

T0nyGTSt Grand Master

T0nyGTSt

Posted
Posted

I used to live around Chetwynd Rd. - there is nothing at all wrong with the road.

Don't be blaming roads for user error.

If you saw the accident photos you'll see the car was split into three pieces... there was a neat cut right at the B-pillar.

I'm guessing the car was doing AT least 80km/h, perhaps even 100+ at impact.

This is certainly unsafe on a spacesaver.

The other tyres were 20" chromes. You think that this would affect the handling of the car?

Merli Grand Master

Merli

Posted
Posted

That photo published in the papers and shown on the smh website linked above was taken at WSID :

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      There are a few different ways of doing it. I'm currently running two 1000cc pre-TB nozzles and PWM the pump for control. I'll be moving over to a constant pressure system and direct port. I'll run the pump off a regular relay, have it cycle on roughly 5psi before I start injecting to build pressure and then PWM a WMI solenoid (It's basically an injector that can take a lot of pressure and not corrode with water and meth.) The solenoid feeds the 6 direct port ~200cc nozzles. I'll also keep one ~250cc pre-TB nozzle to help keep IAT's in check.  Safety will be a little different as well. I used to use a pressure switch but will be moving over to a pressure sensor between my solenoid and nozzles. I'll trigger my solenoid and if I don't see specific pressure within a specific timeframe (e.g 100psi within a second, 175psi within 2 seconds), I kill it and revert back to non WMI maps the same way I did it before with 4D in Haltech. I was just figuring out the timers in my ecu last night. They made that a little more complicated than I would have liked... I wish Haltech offered a larger set of logic/math functions like other ecu's do. I can't do very much with just AND's and OR's.  I've been asked to do fuel/ignition mapping on a medium bore engine at work in May (192L V16). Being the only programmer in my region and having went and opened my mouth about knowing the ins and outs of fuel/ignition mapping, I have now been deemed an expert. Fun fun. The entirety of the logic and algorithms are programmed in C on a PLC. As I spend more time figuring it all out, I like what I see and eventually I may consider doing the same as a pet project to replace my ecu.   
    • Dose Pipe Sutututu
      R32 GTST - 600KW+ RB28/CD009 Build

      By Dose Pipe Sutututu · Posted

      This would be interesting, would you feed it via a 2nd row of injectors? Or just usual WMI nozzles?
    • Milkmun
      Magnetic Drain Plug Snapped in Half

      By Milkmun · Posted

      Cut sump up and extend. Win win 😂 
    • SLVRBAKSLPZ
      Recommended Torque: RB26/30 ARP 1/2 Head Studs

      By SLVRBAKSLPZ · Posted

      All, What's the recommended torque for the 1/2 head studs for RB30 twin cam conversion with RB26 head?  
    • Duncan
      Magnetic Drain Plug Snapped in Half

      By Duncan · Posted

      also, we need to know which solution worked....
×
×
  • Create New...