Jump to content
SAU Community

Recommended Posts

But we arn't talking about 1400rpm in 5th? We are talking about normal driving conditions; keeping up with traffic which may mean 0psi-2psi of boost.

Tune these area's to as lean as they can go (sure reduce a little response but who cares) and you WILL pick up fuel economy. Why tune light/part throttle for maximum throttle response.

Not arguing discussing.

I think I have simply missunderstood your line of thought or missed a prior post or something :(

  • Replies 85
  • Created
  • Last Reply

Top Posters In This Topic

The PFC's closed loop is closed loop, being 14.7:1, you cannot make it run leaner even if you wanted to. Tweaking of the inj. map is really all you can do, this attempts to bring afr's closer to the closed loops target afr.

Datalogit

Settings 1

"O2 Feedback"

Default is 1.047 lambda ie; 15.3 A/F ratio = around 1 volt on the lambda sensor output

Change it to whatever you like as long as the narrow and slow lambda sensor can read it

Tip, lean it out at pre boost rpm (load) and use the acceleration enrichment to get the throttle response

:) cheers :yes:

Im lucky because i can flick a switch and have a totally different Map for max performance or economy,Changes on the fly instantly.

I reckon you have 2 maps, one for "max performance" and one for "poorer performance". The fuel ecomony shouldn't change if the car is driven the same. Efficient combustion for power, is efficient combustion for fuel ecomomy.

Placebo effect, you flick the switch on the ECU for fuel economy and the brain gets switched at the same time. Hence better fuel economy.

The best fuel economy switch is the one under your right foot.

:sweat: cheers :(

PS; yes I have tested it, I set up a car some years ago with an economy/power switch (that did nothing). After a month of testing (the owner thought the switch leaned out the mixtures), bingo the economy position used 12% less fuel. You should have seen his face when I showed him an unconnected switch.

Edited by Sydneykid

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah. Will f**k a tight nut. Will possibly f**k a non-tight nut, if accidentally put on too off-centre. Otherwise... I've always been tempted to buy one to see how good they are. Thing is....I have all the other sockets, spanners, etc. So, unless I was trying to build a 1 socket kit.... see little point.
    • Donut tried them out, they were fine as long as the bolt or nut wasn’t very tight 
    • It is a very complicated plastic tank. Sitting between the rear seats and the rear subframe. Requires a siphon venturi pump in the hat to suck the fuel from the passenger side to the driver side of the tank. The answer is probably prepping the tank very carefully to eliminate all fuel fumes, drilling any cracks to stop propagation, then plastic weld. I don't really see any other solution here. 
    • Does anyone know when your oil drops viscosity, if it is an issue? I imagine with tuned cars they will be overfueling more compared to a stock standard car and will thin out over time. 
    • anyone ever used these ? https://www.ebay.com.au/itm/186214260439?_skw=socket+set&itmmeta=01JEG3TKV388ZXGP8N7CHNCQ45&hash=item2b5b3c1ed7:g:mhAAAOSwwB9lf~Xm&itmprp=enc%3AAQAJAAAAwHoV3kP08IDx%2BKZ9MfhVJKkJwJeiNMm%2FsStacz%2BhjzBowaFnbNCowwe08vVGrW0FbesCs%2Flw%2FQYjDQLjKsuKvgysWT9%2F4b9AZUX3qLP5RDfFhtD8DxufvqBbyZrQAQXuG3h8%2BxxqhWhH8fIfU84eA9W7VIpxDNw9MWj9BdfkkMasYhcqOjTrcKwLyD3ftzZbaZb2Us7%2FFR1Q2kcT68ZYRU77%2F%2BtRr1qBS27BXxh%2FjWBQxhWyUcLlEFIb%2BITZPIKwxQ%3D%3D|tkp%3ABlBMUOy96oP0ZA   I believe the idea being, the rods push back around the shape of whatever nut you put in there. Sounds pretty handy to just need to carry 1x socket in the car for 'most sizes'  but, theory vs reality, anyone tried them?
×
×
  • Create New...