Jump to content
SAU Community

Skyline Service And Performance Question

habibskyline

By habibskyline,
in General Maintenance

 Share

Recommended Posts

habibskyline Enthusiast

habibskyline

Posted
Posted

yo,

My car runs really slow? its a R33 gtst...TURBO.

Ive tested a 0-100km time and it does it in the high 7's and low 8's?

Why is that?

I haven't serviced the car since 15,000 kms ago (I know, bad)

But would a full engine service help my car perform better? I.e chage spark plugs, clean throttle body, clean injectors, change engine oil etc??

Thanks!

Link to comment
Share on other sites
insu Rising Star

insu

Posted
Posted

Yes.

And you haven't stated your mods, how many k's your car has done, your cars current power output, suspension setup/state of, way you're measuring your times and the way you're driving your car in order to get those values. Also if your car is running funny, ie currently exhaust leak etc.

If you provide all this information you'll probably get alot more help from the guys on here.

-Insu

Link to comment
Share on other sites
HR32_GTS-T Rising Star

HR32_GTS-T

Posted
Posted

get the hole i ur exhaust fixed or get a new system, just a question where does the temp gauge sit?, if u have a leaking radiator this can result in it not pressurising properly, i had this problem in my VL, hole in zaust made my car use more fuel an run like a bag of spuds on wheels, i couldnt even beat a berina.

Link to comment
Share on other sites
insu Rising Star

insu

Posted
Posted

Also, the times posted for an R33 0-100 times in the high 6 second mark are for manual cars, you'll loose a bit (up to a second by some reports) of power through the auto box, it's just the nature of them.

If you got the car all serviced and running well, i'd expect times in the low 7's with an auto would be reasonable.

Get the car dyno tuned to get a good idea if the actual power output for the car is healthy or not, that way you can also check your fuel air ratios as well.

-Insu

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Does anyone know whats happening with harness on drivers door?

      By GTSBoy · Posted

      The two diagrams are equivalent. The R32 one is just one sheet out of about 3 showing everything in the whole car all at once. And without knowing the functionality that occurs in the modules, they are both equally opaque.
    • Neostead2000
      R35 OEM Injector dead times

      By Neostead2000 · Posted

      8v - 2.48ms 9v - 2.15ms 10v - 1.74ms 11v - 1.41ms 12v - 1.15ms 13v - 0.99ms 14v - 0.89ms 15v - 0.82ms 16v - 0.81ms I'm running these values on my RB20 Neo with 570cc Denso R35 stock jets and it's great. Also bought a set for my Legnum VR4, love these injectors!
    • harambe34
      Does anyone know whats happening with harness on drivers door?

      By harambe34 · Posted

      Thanks for your reply,  Those blue/green wires running to the actuator aren't attached to anything, so I'm not sure how the central locking is still working. I will have to take a good look tomorrow, I don't have the car with me. After googling it seems like a pretty common aftermarket actuator which even uses the same green/blue wires the immobiliser required. i'll test everything tomorrow and if it's working i'll melt the solder, strip it, resolder and neaten it all up with some heat shrink. I don't have to understand it if it works hahaha I just don't want a fire/ short circuit. That R32 diagram looks more like a continuity chart? Can you make sense of this form the R34 manual? 10V is probably due to very flat battery, i'll recheck as well tomorrow, I did have to jump start it haha. Thanks again!  
    • GTSBoy
      Does anyone know whats happening with harness on drivers door?

      By GTSBoy · Posted

      So, COM doesn't mean comms. It means common. What common itself means will depend on the type of device. For a two directional actuator (ie, one that can push and pull on the same output rod) then the common will typically just be the earth connection. There will be at least 2 other wires. If you put 12V on one of the other wires, then the actuator will push. On the other 12V wire, it will pull. Can't quite make out what is going on with the wiring of your actuator. It appears to have several wires at the actuator plug, but there only appears to be 2 wires where its loom approaches the door control module, with at least one of the others cut off. I don't know these actuators off by heart. I'd have to look at a wiring diagram for one before knowing what the wires were about, and that's despite me having to replace one in my car not all that long ago. Just not interesting enough to have dedicated memory set aside for trivia like that any more. That actuator is an aftermarket one, not the original one, which probably died and was replaced. That might require some sort of bodge job on wiring to make it work. Although nothing should justify the bodginess of the bodge job done. As to the soldering job on the door module's loom plug. Ahhahhahaha. Yes, very nasty. Again, I cant tell you what any of those wires do. You'd need to study the R34 wiring diagram (if you can find one that shows the door module). I don't think I have any. I'd have to study the R32 diagram to start to understand what mine is doing, and again, even though I've had a problem with mine for the last 25 years (where it locks the passenger door when the driver's window reaches top or bottom of travel) I'm just not interested enough to try to to work it out. So long as it's not burning down, it's fine with me. Here's the R32 GTR diagram, which, confusingly, has rear door lock actuators and window motors on it!! As you can see, unless you understand the functions of the door lock timer and the power window amplifier, you'll never be able to work out how it works just from the diagram. I don't imagine that the R34 one is any better. Hopefully an R34 aware bod can help. FWIW, the two wires that are cut and joined look like they are both power supply - so hopefully it is not fatal to join them. The 10V you measured on the cut off free end of one of them is concerning. You'd expect 12V, and it might be the reason for the bodge job joining them together.
    • harambe34
      Does anyone know whats happening with harness on drivers door?

      By harambe34 · Posted

      Oops my bad, here you go .
×
×
  • Create New...