Jump to content
SAU Community

Recommended Posts

i just did it on my R32 (rb20det)

took about 30mins, had the ecu out too, but didn't have to touch it. I used combustion chamber cleaner instead, and set the idle to 900rpm warm...up from 600rpm (factory spec)

idle's much smoother, no more stalling issues with the hks ssqv, annoying stalls with the A/C on, or stuttering when clutching in and decellerating.... or rpms dropping when im driving with the headlights on and heater on at night. this is such a wicked faq. there is no excuse not to clean/inspect your AAC valve!

THANKS INSU :thumbsup:

When I took mine off for the clean I took the idle adjust screw all the way out. Around it was a rubber sleeve. Now whenever I try to screw it back in the sleeve just rolls up the screw and I'm concerend that air may leak in through any gaps.

Anyone got any suggestions on how to get this rubber to seat on the screw inside the thread again??

What else do you do when you're playing with a screw and you can't get the rubber in?? Whack a bit of lube on it! :mellow: Bit of Vase', you'll be fine.

I believe the rubber is only there to prevent the screw from adjusting with engine vibration and such.

  • 2 months later...

this solved the fluctuation in the revs and stopped my car from stalling. it only take about 30 mins if you know what your doing. i didn't even have to adjust the idle after it was perfect.

even if you dont have rev or stalling problems i highly recomend you do this.

BIG THANKS to INSU for this diy

i don't hate my car anymore thanks to you!!!

great tutorial, helped me immensely in cleaning my aac valve on my r32 gts-t. two things i have noticed though, on my car you had to disconnect the TPS rather than the brown plug on the AAC valve to adjust the AAC idle as you would on an r33. secondly, did anyone else find it ridiculously hard to screw in the idle screw while adjusting the AAC valve idle? i dunno why but i got it down to about 900rpm and its pretty much stopped moving.

anyways thanks again dude great writeup!

great tutorial, helped me immensely in cleaning my aac valve on my r32 gts-t. two things i have noticed though, on my car you had to disconnect the TPS rather than the brown plug on the AAC valve to adjust the AAC idle as you would on an r33. secondly, did anyone else find it ridiculously hard to screw in the idle screw while adjusting the AAC valve idle? i dunno why but i got it down to about 900rpm and its pretty much stopped moving.

anyways thanks again dude great writeup!

If it was ridicuously hard to turn, probably the O-ring on the AAC Value screw is all dry and crumbling. Time to replace that O-ring.

When I took out my AAC value, I removed the screw, the Solenoid, the piston and spring inside and gave it a good clean with carby cleaner. Put it all back together using carby cleaner as a lubricant and replaced the old tired O-ring. Cost my $0.50 for the O-ring.

If it was ridicuously hard to turn, probably the O-ring on the AAC Value screw is all dry and crumbling. Time to replace that O-ring.

When I took out my AAC value, I removed the screw, the Solenoid, the piston and spring inside and gave it a good clean with carby cleaner. Put it all back together using carby cleaner as a lubricant and replaced the old tired O-ring. Cost my $0.50 for the O-ring.

Did you ask for a receipt?

Did you ask for a receipt?

I've just got to the stage where I have pulled it out ready for cleaning. Jeez it's fiddly!!

I'm looking in your pics as when I pulled the last hose off I think I knocked some bit of plastic or something down around and settled in the many cavities beside the engine. Can't see it, I hope I remember to jack the car after all this and see if I can see it from the bottom.

Wierd thing is I can't see any clips or other bits I am missing (compared with your photos)

I guess that's what I get for doing things at night :)

Hope it fixes the occassional hunting.

My car will be fine for a month or so - then a hot day or add the A/C and you'll get rev hunting for 5 minutes or so..

quite random..

Ok - all done. Cleaned it up..but I got a hint of the hunting again today. maybe part of it is faulty?

Anybody else found this.

It will be ok for a few days then for a bout 30 seconds the idle will fall and rise...the injector duty cycle stays the same (I have PFC)..

Sounds very much like it is the AAV and that is why I cleaned it.

The funny thing is that my idle is pretty much perfect, but adjusting the ECU's fine adjustment screw does nothing at all, winding left or right does not affect my idle.. weird.

Is it because I'm using a remapped ECU? with the rev limiter taken out?

I tryed this today and all was going well, i adjusted the idle with the brown bit unplugged (i have a 1989 R32 Skyline) and then plugged back in, revs were nice at 1000rpm then i turned her off, started her up and instantly the revs were up around 1600rpm. i then tryed again this time with the TPS disconnected and then re-connected and the best i can get is about 1500rpm (including adjustin the ECU idle).

Seems to backfire and burble on engine breaking a lot more but still feel smooth when driving

Could this be leaks or should i now try the IAC valve under the throttle body?

initial reason for cleaning the AAC valve was idle hunting and stalling which i still suspect to be a dodgey BOV but now i cant get the engine to idle how it used to (even if it was stalling).

Edited by god's rx

I just cleaned mine out, alot easier than i thought...took about 45min for a beginner.

Yea i also had troubles putting the idle screw back in, but what i did was unscrew it out, then back in, back n forth pretty much until it found its way back in the hole pretty smoothly. Now my idle sits steadely on 900rpm wen warmed up. Great DIY Insu, solved my stalling issue. :happy:

My ECU adjustment screw does nothign aswell, not a thing. I have cleaned my ACC valve ect, but on the R33 if i disconnect the Tp it does not idle below 900rpm, eaven with the ACC screw all the way in. No go for me. I think my Cold start valve is stuffed or not closing.

I have tested for air leaks, but no good there either.

just performed on my 32 and went sweet, really helped all the problems! One thing though..when i was adjusting the idle screw on the side of the ecu, it didnt nothing at all and i think i may have gone past the 12 o'clock point! Is this ok, any side affects? It did nothing to my idle!

just performed on my 32 and went sweet, really helped all the problems! One thing though..when i was adjusting the idle screw on the side of the ecu, it didnt nothing at all and i think i may have gone past the 12 o'clock point! Is this ok, any side affects? It did nothing to my idle!

The ecu is only meant to adjust the idle in 50rpm increments from memory, and should only be used if for some reason your car isn't idling as it should from the idle by-pass screw. Even through the whole range of the screw which is like 70deg or something, there isn't much adjustment there.

I wouldn't worry about it too much, cause i've never heard of anyone having to use the computer adjustment.

As for going pas 12 o'clock, if you do it puts the car in diagnostic mode from memory. Shouldn't be a problem if you turned back. If you turned it beyond 3-4 o'clock i think it is thou, you can f**k the little switch, so don't do that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi. A little bit of an update. It maybe(hope not) looks like i would need a new tranny(it would be "maybe" a cheaper or better option anyway) So i need some info. I know i need a different propshaft(i can make custom one) LSD is not a problem cuz the engine will be still(for now) N/A RB20. So if i buy RB25DET NEO tranny...is there something else i need? I read something about push/pull type but i do not know if i need to "change" something or i can just plug n play onto my engine a go? Thanks for the advice  
    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
×
×
  • Create New...