Jump to content
SAU Community

Recommended Posts

Moving house in 5 weeks, garage is full of car crap, time to get rid of this stuff.

Firstly the original RB20DET engine from my a31 Cefiro. This was cooked pretty good when a radiator hose burst. Still was running but overheated after 10/15 minutes without fail. Compression test not pretty. Suit decent rebuild/spares.

Includes turbo, power steering pump, air con compressor, rusty old flywheel and clutch, alternator. Will seperate parts.

Loom and electronics can be provided or seperated. Pretty much entire entire loom minus afm from auto a31 cefiro including ECU. Never tested this, just swapped my old loom over. Includes ignitor chip, coilpacks, CAS, etc.

engine2.jpgengine1.jpg

loom.jpg

$300 for everything.

S13 subframe from my old 180sx. Straight as a die, complete except for toe rods. Includes hubs and studs. $100.

subframe1.jpg

180sx tail lights from my old 180sx. Perfect condition, no scratches/cracks. $50 pair.

taillights.jpg

Complete rear brake setup from s13. Includes discs, calipers pads, and complete handbrake assembly and cable. Perhaps ideal for rear disc conversion on older car? $50 the lot. Alloy coolant temperature probe housing (on far right in red)$20

stuff5.jpg

S13 front and some rear inner plastic guards. Good condition. $40 the lot SOLD

innerguards.jpg

Heaps of misc trim, spares, etc. What you see is what you get. Free to good home(s). Will post if buyer pays postage. standard fee of $10 for such items, that way I might make $3 an item for my trouble. May or may not include free spiders from my shed. Vague descriptions of what is seen in each pic below.

stuff1.jpg

Instrument surround, glovebox, interior trim, washer water bottle with filler neck, steering column trim all from s13.

stuff2.jpg

Centre console, air con under dash ducting, interior trim, hacked r32 skyline airbox, castor rod.

stuff3.jpg

Antenna mechanism, rear 180sx trim: speaker supports, etc. Misc induction system airboxes.

stuff4.jpg

Dented sr20det sump, 180x rear speaker supports, myriad of engine bay supports and brackets I deemed 'too heavy', 5 bolt drive shaft good except dodgy thread on end, good but restrictive catalytic converter, airbox chambers, spare s13 rear hub with rooted wheel bearing.

seat1.jpgseat2.jpg

s13 rear and drivers seats.

Please PM or email [email protected] for further enquiries. Located in Blue Mountains, 40 mins up from Penrith, NSW. Most things that aren't sold will simply be binned within the month.

Cheers,

Michael

Edited by l6a6w6s6
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 1. Factory knock sensors for now, honestly the RB26 OEM knock sensors seem ok as they're flat response instead of resonant type but they appear to be internally grounded to the block. If I do replace the sensor it would just be to get ones that are not internally grounded so a differential input can be used to reject common mode noise. Definitely plan on fixing this as a part of the tuning process. 2. Never deliberately induced knock, though I guess I could try that experiment if I really wanted to. 3. All of this is basically on a stock engine + ECU, only modification is HKS GTIII-SS turbos and a Nismo plenum. Currently I run it with the wastegate solenoid unplugged so it won't try to raise boost past wastegate pressure.
    • After being peer-pressured into paying $100 for the MW remakes, got BO6 on XBox Game Pass. I think that's worth it.
    • That's a given!  Bit hard to powdercoat it properly without removing them! 😁
    • No detail on compressor or turbine sizes, which doesn't help with housing size selection with that kit. However, from SR20DET mucking about and money torching perspective, a GTX2860R Gen 2 w/ 0.64 (46mm inducer) will do ~260kW on E85 about 1.5bar of boost. All in before 3000pm, which cause a gearbox to shatter. Now imagine the same turbo, on a modern motor with an extra 0.5L of displacement, and heaps of cam timing adjustability (not an on/off affair like the Nissan shit boxes). If this was my car (which I would never own or consider buying, ever!), I would go for a nice twin scroll setup, and a G30-660. Gates plumbed back, no silly shit. Lean on the cam timing, big displacement to create a flat-ish torque curve.  
×
×
  • Create New...