Jump to content
SAU Community

Recommended Posts

It seems no one has discussed replacement bushes.I have developed a clunk in my front end when reversing out of the driveway or turning into a corner.This could be the king pin or ball joint, however I was cruising through the Planet soarer forum and seems replacing the rack bushes may well be in order.

Now if this is the case,then what would be better,urathane or rubber.After replacing my rear upper arm and front caster bushes with urathane I didn`t notice any difference in noise or vibration.Would the steering rack be any different?The rack is after all very close to the steering wheel and a guy in Planet Soarer said his steering was was much better after pulling out his urathane bushes and putting in brand new rubber ones.

Having sorted that out, where would I be able to get them in sydney (cambelltown).How much?

HELP ! >_<

Link to comment
https://www.sau.com.au/forums/topic/110977-steering-rack-bushes/
Share on other sites

I replaced mine with urethane ones from fulcrum suspension as my old ones were shagged (drivers side came out in 3 pieces)

Its a simple job to do, and im glad i did it.

There is no increase in NVH at all, and turning seems a little crisper.

I undid the top bracket that secures the rack to the x member, then manuverd the rack up a little (didnt have to disconnect any ps lines) and just slid the old ones out. The new ones from fulcrum had a slit in them same as std, so i just slid them in, and replaced the tops on.

i was doing tie rod ends at the same time, so it made it a bit easier too...

rackrubber.jpeg

Edited by Bl4cK32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...