Jump to content
SAU Community

Steering Rack Bushes

skylinecouple

By skylinecouple,
in General Maintenance

 Share

Recommended Posts

skylinecouple Experienced

skylinecouple

Posted
Posted

It seems no one has discussed replacement bushes.I have developed a clunk in my front end when reversing out of the driveway or turning into a corner.This could be the king pin or ball joint, however I was cruising through the Planet soarer forum and seems replacing the rack bushes may well be in order.

Now if this is the case,then what would be better,urathane or rubber.After replacing my rear upper arm and front caster bushes with urathane I didn`t notice any difference in noise or vibration.Would the steering rack be any different?The rack is after all very close to the steering wheel and a guy in Planet Soarer said his steering was was much better after pulling out his urathane bushes and putting in brand new rubber ones.

Having sorted that out, where would I be able to get them in sydney (cambelltown).How much?

HELP ! >_<

Link to comment
https://www.sau.com.au/forums/topic/110977-steering-rack-bushes/
Share on other sites
Bl4cK32 Grand Master

Bl4cK32

Posted
Posted (edited)

I replaced mine with urethane ones from fulcrum suspension as my old ones were shagged (drivers side came out in 3 pieces)

Its a simple job to do, and im glad i did it.

There is no increase in NVH at all, and turning seems a little crisper.

I undid the top bracket that secures the rack to the x member, then manuverd the rack up a little (didnt have to disconnect any ps lines) and just slid the old ones out. The new ones from fulcrum had a slit in them same as std, so i just slid them in, and replaced the tops on.

i was doing tie rod ends at the same time, so it made it a bit easier too...

rackrubber.jpeg

Edited by Bl4cK32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      CD009 RB Conversion

      By TurboTapin · Posted

      That is correct. I'm using a modified ABS ring and a ZF speed sensor on my rear diff for speed input. I'm running a Haltech ecu. 
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Been busy with the newborn. We originally thought we were going to go for a third, but we're good with two lol. He's starting to actually sleep now so I've had some energy to work on the car. It's been parked away in the garage since late November due to winter.  I went ahead and redid all my head oil drains. I originally had my front and rear head drain going into the same pipe but have since split them up. I also added an Ethanol content sensor to get ready to run E85 this summer. Tossed it on my return line. Sensor sits nicely under my intake manifold.    I also have a lot of parts that came in for my rear end. I'll be swapping over to a 3.3 final drive and doing the GK teck anti squat mod. While the rear subframe is off, I'll also change every bushing. We're planning on buying another house soon with the condition that I get at a minimum a 2 door garage, so I'll wait to have more room for this. Now onto the strange things that recently happened... After changing the lower rad hose (It had been sitting in my cabinet for well over a year and was the last hose I had to replace), I let the car idle in the garage to bleed my coolant. After running for a few minutes, it started missing. Got much worst within a minute or two and then stalled and would not restart. My crank sensor decided to crap itself. No damage, no explanation, just died. I went ahead and replaced it with another ZF sensor but the heavier duty stainless model with a shield. Tossed that in and started right up. Has anyone else seen this? I hate when things fail without cause. Luckily this was a blessing in disguise... This lead me to recheck my timing. It seems I may have had a beer or two the last time I had set my TDC angle as I was off exactly 5 degrees... I miscounted a line haha. I was running 5 degrees less then commanded. It's a little embarrassing but helps explain why my dyno operator seemed to think I should be making more then 478rwkws.        
    • hypergear
      Hypergear Turbochargers and High flow Services Development thread

      By hypergear · Posted

      Sharing results from recent Liberty Walk R35 GTR, since they are still considered as somesort of a V36 Skyline. We do them turbos too. This are high flowed SS-1 models with ball bearing conversion done.  Car have managed to pull 485awkws @ 20Psi so far pushing limitations of factory built engine. The build list for R35 GTR enthusiasts as follow : HyperGear high flowed stock turbos in SS1 (G25-660 specs) Custom titanium intake pipes. Vspec performance titanium front pipes. Vspec performance 4" titanium exhaust. Upgrade fuel pumps. 1200cc injectors. Ignition coilpacks Hks intake plenum. Hks intercooler piping. Greddy intercooler. Greddy bovs. Top-secret coolant reservoir. Emtron ecu. Straight E85. Built gear box.  
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
×
×
  • Create New...