Jump to content
SAU Community

Standard R33 Bov


Ganador
 Share

Recommended Posts

how do you run the standard BOV with out the plumb back and have the engine not stall???

Ive tryed dissconnecting the plumb back then blocking it off, bu the engine keeps stalling. its able to rev high and make some loud noises but just wont idle..any help?? and how is that plumb back eliminated all together cause it looks gay.

Edited by Ganador
Link to comment
Share on other sites

how do you run the standard BOV with out the plumb back and have the engine not stall???

Ive tryed dissconnecting the plumb back then blocking it off, bu the engine keeps stalling. its able to rev high and make some loud noises but just wont idle..any help?? and how is that plumb back eliminated all together cause it looks gay.

AFAIK you can't, the stock BOV leaks all the time, even at idle. So you will never be able to get the car to run with the re-circ pipe disconnected. If you really want a VTA BOV then you will have to replace the stock BOV with an aftermarket BOV.

Link to comment
Share on other sites

WRONG

if you want to get the stock bov working without hte plumback, the solution is not an aftermarket bov, but an aftermarket ecu...

I have a top of the range turbo Smart BOV with a Power FC and its still not perfect, the problem being that after it vents there is still a small flutter (with large snail) causing air to go both directions in the AFM causing Power FC to freak! the computer thinks ok more fuel and if large injectors ie. 720cc thats heaps of fuel and bam a stall.

Sorry no answers only more problems, my advice stick to factory BOV system (or smaller injctors haha)

G.

Link to comment
Share on other sites

im looking at putting a front cooler, turbosmart type2 BOV, gizzmo electronic boost controller and this turbosmart thingy that can be adjusted so when you up the boost the computer wont get confused. i think this should pretty much solve problems all round.

Link to comment
Share on other sites

I have a top of the range turbo Smart BOV with a Power FC and its still not perfect, the problem being that after it vents there is still a small flutter (with large snail) causing air to go both directions in the AFM causing Power FC to freak! the computer thinks ok more fuel and if large injectors ie. 720cc thats heaps of fuel and bam a stall.

Sorry no answers only more problems, my advice stick to factory BOV system (or smaller injctors haha)

G.

First time ive heard of injectors causing a car to stall....

Link to comment
Share on other sites

First time ive heard of injectors causing a car to stall....

I know its weird, its not so much the injectors but the AFM reading air coming back in on the flutter and then of course the over dose of fuel.

Best of luck with all the mods, I'm sure they will all be sweet together.

Link to comment
Share on other sites

WRONG

if you want to get the stock bov working without hte plumback, the solution is not an aftermarket bov, but an aftermarket ecu...

You sound very sure. :thumbsup:

Have you tried it, the stock BOV cannot be used as a VTA BOV because it leaks at idle, it has nothing to do with the ECU.

Link to comment
Share on other sites

well i was being a bit definate there wasn't i.. he he

what i meant to say is that changing to an afermarket bov is NOT going to fix the problem

the problem is that air that has been accountered for is being lost

Putting another device that loses air will simply return the same problem

the only way to fix it is to either:

- put a re-circulating bov on the car (stock or aftermarket)

- use a decive that accounts for the lost air, thus keeping the AFR in equilibrium

Waz

Link to comment
Share on other sites

the stock BOV cannot be used in a VTA situation because the spring is too soft and cannot be adjusted.

You can run an aftermarket VTA BOV with the stock ECU, you just have to adjust it properly. If it's stalling then the spring is probably too soft and staying open too long.

The only problem with VTA BOVs is running rich during gearchanges when the BOV vents

I was running a Greddy Type S and now a GFB StealthFX, both with no problems with stalling whatsoever.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • They should do. I have S14 (or something S chassis, anyway) driveshafts in my R32 (because my diff flanges have 3x2). They're the right length. When you go looking for R32/3/4 driveshafts (for turbos), they're all the same thing, so are the same length. So there really shouldn't be any reason why those cheapies from JJ won't also fit an R34. R32/3 NA should also be the same thing. The (3x the price) D-Max ones are uni-fit. They have 5x1 and 3x2 bolt holes and say they cover all the cars. So that would also suggest that they are all the same except for the flanges. And in that case, the flange goes both ways. I'd be buying the D-Max ones if I ever have to replace a shaft. Because that will open up diff options without needing to juggle shafts also. Juggling shafts is gay.
    • Yeah with the adaptors they do look like the photo above - just the fitment within the plenum itself and then further with the rail to the intake is questionable - we shall see tomorrow hopefully once I get some replies from Aeroflow, maybe those bosses are the missing piece....
    • Should be fine, if you have it sitting too far in, you end up just spraying the walls and have shit idle. You "can" run them like that, however I don't think it's a great idea (also depends on your plenum, might be good to just get the injector bosses first, mock it up and see if you need to get the bottom extension) Ideally your injectors, with the extension should look like this  (Not my photos, just Google)
    • Thanks for the replies guys, it's really appreciated.  It seems the kit was supposed to come with those injector bosses but hasn't. Unsure if they'll help as even with the adaptors to make them a 3/4 height injector they still sit too far out so mount the fuel rail?
    • Hello, I am looking to replace my two rear drive shafts in my R34 N/A Skyline but I'm finding conflicting information. Do S13/S14/S15 or R32 NA/ R33 NA fit? https://justjap.com/products/gsp-premium-rear-drive-shaft-l-h-nissan-silvia-s13-s14-s15-3x2-type?currency=AUD&srsltid=AfmBOoqY7EwDaYCUoUU3mxxZ_qrUXkVVHiV4MIN7ozoar6scjnEiekv- would this fit?
×
×
  • Create New...