Jump to content
SAU Community

Recommended Posts

  • Replies 64
  • Created
  • Last Reply

Top Posters In This Topic

Unlucky mate, did you get the standard BOV when you purchase the car ? If so just fit that one on, cause all aftermarket BOV that vents into the atmosphere are illegal. I think you can get permits for the neons now days, correct me if im wrong. And yeah get yourself some decent rubbers dont want to be power drifting on a wet day all over the road haha.

Link to comment
https://www.sau.com.au/forums/topic/112538-yellow-sticker/#findComment-2074785
Share on other sites

Neons are legal, provided you only see the glow/hue of them, if you can see the light source itself when they are on, you need to fix that up..

bov, provided its not too loud should pass

tyres are tyres, if they are legal go over the pits with them

as for the parcel shelf, provided there has been no steel cut out of it, should be fine, if it has had steel cut out, its a 10k fine for wheoever did it if its a shop, and i think you may be liable for a fine if it was you..

easiest thing to do is run it over the pits and see what they say, 90% of stickers are just time wasters

Link to comment
https://www.sau.com.au/forums/topic/112538-yellow-sticker/#findComment-2074791
Share on other sites

ahh... unlucky dude,

I had neon’s on my old car they were blue, got over the pits no worries and got permits. Just make sure there secured properly, tubes aren’t visible, are on a separate switch which has an inline fuse on it.

Not sure about BOVs i think there legal if there not too loud or vent into the atmosphere.

Good Luck at the pits, hope all goes well.

-michael

Link to comment
https://www.sau.com.au/forums/topic/112538-yellow-sticker/#findComment-2075638
Share on other sites

I agree with Wildcat i thought that red neons were not legal...

Not 100% sure on that though.

ATMO BOV's are definitely not legal. Chuck the stocker back on, if you do not have it chuck a post up. One of the fine folk on the forums will lend you one.

Link to comment
https://www.sau.com.au/forums/topic/112538-yellow-sticker/#findComment-2075766
Share on other sites

well i just bought this car off a dealer like 2 weeks ago and what he did to get it over the pits is just disconected the BOV and the tires also past. cops didnt get me for my pod wonder why. also i took out the child restrainers and put 6*9 in so i guess i just put the child restrainers in. or yous think i will pass with the 6*9s in the back shelve??

Link to comment
https://www.sau.com.au/forums/topic/112538-yellow-sticker/#findComment-2076150
Share on other sites

well i just bought this car off a dealer like 2 weeks ago and what he did to get it over the pits is just disconected the BOV and the tires also past. cops didnt get me for my pod wonder why. also i took out the child restrainers and put 6*9 in so i guess i just put the child restrainers in. or yous think i will pass with the 6*9s in the back shelve??

the reason they didnt do you for pod is because pod filters are legal nopermit is required refer ei-107a fro dpi

EI-107A

Vehicle Safety Branch Examiner’s Instruction

Vehicle Intake and Exhaust Systems

Pre ADR 27C Vehicles

There is evidence to suggest that many ‘hang-on’ emission control devices for these vehicles

are no longer available from original equipment manufacturers and/or spare parts suppliers.

This applies to vehicles manufactured prior to 31 January 1986.

Taking into consideration the non-availability of emission control components, examiners do

not need to insist on original equipment emission control systems being intact.

Consequently vehicle examiners do not need to issue a modification permit for exhaust

extractors.

It is also unnecessary to issue a modification permit for non-genuine air filters providing

induction noise is not excessive. These include cone or pod type filters.

Not withstanding the above, vehicles must continue to comply with the Road Traffic (Vehicle

Standards) Rules 2002 with respect to the emission of smoke.

Post ADR 37 Vehicles

Vehicles manufactured from 1 February 1986 must continue to comply with the applicable

design rule for the year of manufacture (Australian Design Rule 37/00, 37/01, 79/00 or

79/01).

Catalytic converters and other emission control devices must be retained and functioning

correctly. However where exhaust extractors are fitted a modification permit is not required.

It is also unnecessary to issue a modification permit for non-genuine air filters providing

induction noise is not excessive and that all engine management sensors are fitted and

operating. These include cone or pod type filters.

EI-107A (Feb 05) Application date Feb 05 page 1

Link to comment
https://www.sau.com.au/forums/topic/112538-yellow-sticker/#findComment-2076501
Share on other sites

I agree with Wildcat i thought that red neons were not legal...

Not 100% sure on that though.

ATMO BOV's are definitely not legal. Chuck the stocker back on, if you do not have it chuck a post up. One of the fine folk on the forums will lend you one.

Yeah I have read that red and blue neons were illegal as those colours are reserved for emergency vehicles (think there was a thread previously about it).

JB

Link to comment
https://www.sau.com.au/forums/topic/112538-yellow-sticker/#findComment-2077081
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I’ve got one on mine and it’s fine, 
    • No, you don't want to plug the vacuum line, as that will turn that side of the booster into an air spring and probably make it feel worse. I'm not saying that the GTR master itself doesn't need a booster. I haven't paid attention to the GTR one to know what size it is cf the non-GTR ones. But when you think about it - they have to do the same job, which is to move a little slave piston a few mm to do what it is supposed to do, and that final action is the same on all the cars. So, it is very unlikely that the GTR MC is any different than the others, because it has the same pedal stroke and the same output requirement. The booster just makes it feel easier. I'd suggest you probably have an actual hydraulic problem. It's totally common on these old shitboxes.
    • Ye, in terms of bolting up the "Conversion" from a GT to a GTT is effectively "Use GTT parts for everything" Except the subframe itself, because you won't want a HICAS/4WS subframe. Remember your ABS system will be different too, thanks to GT being the S15 3 sensor system, instead of the R34 4 sensor system for wheel speed. I do not know how people get this to work given R34 diffs do not have a provision for an ABS sensor (they are on the tone wheels of the axles). I assume***** people use S15 gear/R34NA forever when they realize this - Or they convert it to a rear diff/axles that are R33 style which I presume has the singular speed sensor on the diff itself, but then you have to wire it all in and...and... and...
    • Foreshadowing was never so easy.
    • The ones in brackets are the first stages of tightening. I usually aim for the middle of the range. They give a range because it's actually not that critical to hit exactly the right bolt tension. Enough is enough, and too much is too much, and the range given is inside that range. Half of the bolts in the suspension are problematic for putting a torque wrench on anyway, so just get done up to mechanic tight  and spanner checked a week later.
×
×
  • Create New...