Jump to content
SAU Community

Recommended Posts

Im looking at putting a r32 gtr fuel pump into my r32 gtst, Ive read that the pump goes in without any modification, but what about the loom, does it have to be modified at all??Is the standard fuel pressure regulator ok with the gtr fuel pump as ive been advised to get an adjustable regulator???

Any advice or tips would be very much appreciated

Cheers

Link to comment
https://www.sau.com.au/forums/topic/112583-gtr-fuel-pump-into-gtst/
Share on other sites

standard reg will be fine.. as long as its in good condition.

loom is different.. a bit of chop and solder will fix that. Its pretty simple.

Which wires need to be cut and rejoined???Any chance you or someone else has some pictures, they would help me out heaps.

Cheers

How many years is a fuel pump good for? You could be putting a 17 year old fuel pump in a 14year old car???

My cars 17years old anyway (its a 1989 gtst), so its not like im putting a older pump in a newer car, im going for the gtr fuel pump because of ease of fitment, i dont want to be mucking around with aftermarket pumps (changing wiring,lines and mounting it) so the gtr pump seems to be the easiest solution,and quite cheap to at $250 N.Z :)

Edited by nizmo_freek

If a workshop told you that you require an adjustable reg with the GTR pump... dont go there again.

Stock fuel reg is fine. You just need to make sure you have good voltage going to the pump.

Read the DIY section (5 or so section below this) it has a pump install guide for the bosch, the voltage part will be the same :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sharing results from recent Liberty Walk R35 GTR, since they are still considered as somesort of a V36 Skyline. We do them turbos too. This are high flowed SS-1 models with ball bearing conversion done.  Car have managed to pull 485awkws @ 20Psi so far pushing limitations of factory built engine. The build list for R35 GTR enthusiasts as follow : HyperGear high flowed stock turbos in SS1 (G25-660 specs) Custom titanium intake pipes. Vspec performance titanium front pipes. Vspec performance 4" titanium exhaust. Upgrade fuel pumps. 1200cc injectors. Ignition coilpacks Hks intake plenum. Hks intercooler piping. Greddy intercooler. Greddy bovs. Top-secret coolant reservoir. Emtron ecu. Straight E85. Built gear box.  
    • Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
    • Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
    • A Brumby would probably fit a big metal toolbox in the back... this is how it begins  
    • Picked up a new OEM boot seal for the MX5 today as the old one got ripped a bit by me being a idiot by seeing if I could fit a large metal tool box in it, it didn't fit, and ripped the seal with the corner of the tool box I am still waiting on time to get the cams and new balancer installed, as well as the repairs to the boot Time will not be an issue soon though
×
×
  • Create New...