Jump to content
SAU Community

Recommended Posts

i hooked mine upto the doors from the i think it was red/blue wire running along the skirt near the boot latch on the floor next to the drivers seat in my 32 :P works when my doors open and when my alarm turns off, the neons fade on with the interior light :D

Link to comment
https://www.sau.com.au/forums/topic/112847-neons/#findComment-2081174
Share on other sites

actually, there was a discussion about this in anotehr thread...

i know qld u can have neons, provided the bulb isnt showing, and you dont have emergency colors.. eg, red, blue, white, yellow..

best check up on vic.. u can normally find a pdf act on vehicle mods, and there should be a small section on " lighting "

not too sure on the installation though, sorry =(

Link to comment
https://www.sau.com.au/forums/topic/112847-neons/#findComment-2081216
Share on other sites

Hi bluer33,

I regards to Neon lights (additional vehicle lighting) in Victoria, the following points may be useful to you. I have used these guidelines for the last few years on many cars and have had no major difficulties.

1 - Additional lighting must not impede access to the vehicle

2 - Additional lighting must not interfere with or impede safety features

3 - Modifications for additional lighting mounting points must not protrude from the body ( see vic modification guide)

4 - Additional lighting must have a seperate on/off function and cannot be directly linked to an existing vehicle system ( doors, lights etc)

5 - forward facing lights must not be red

6 - rearward facing lights nust not be clear

7 - red or blue light is permitted as long as they are not on the vehicle at once

(ie cannot have blue neon at rear - brake lights are red)

8 - lights must be of one color and cannot flash, rotate or turn

9 - instalation must include, on/off switch, fusing

For any additonal lighting for the vehicles interior, it must

- have an on/off switch and not rely on an existing car circuit

- be mounted in such a way that the source of light cannot be seen ( only the glow can be seen)

- be mounted in such a way that vehicle access or safety devices remain effective

- not be mounted within 300mm of the drivers or any passengers head in a normal driving position

In summary.

Green or purple are the safest colors, however no matter what you put on your car external neon wise, they really act as a magnet for the wrong type ( boys in blue) attention.

If you are prepared for this, perhaps you could consider LEDS over neons.

The advantages will be

- generally smaller lights to install

- brighter than neons

- last longer than neons

- LED's are more likely to be clean (electrically) and not give you that annoy pop through your stereo every time they turn off/on

- LED's use less power

Many retailers are now getting out of Neon with LED taking over, of all the retailers i have visited lately, an unlikely one has the best range and prices - Repco.

Please note this information is given in good faith, fitment of any products should always be done by a qualified person.

Hope this information helps.

FRX026

Link to comment
https://www.sau.com.au/forums/topic/112847-neons/#findComment-2081238
Share on other sites

i hooked mine upto the doors from the i think it was red/blue wire running along the skirt near the boot latch on the floor next to the drivers seat in my 32 ;) works when my doors open and when my alarm turns off, the neons fade on with the interior light :mad:

i havent got red/blue wires. there are three yellow, black and red. what happend was red and black works only wen door is closed. i have being playing with the three wires but got nothing apart from the little head ache when door closed. can someone point me to the light plz ;)

Link to comment
https://www.sau.com.au/forums/topic/112847-neons/#findComment-2081414
Share on other sites

Hmm, has been a while since i did it, so the colours may be wrong, umm i got a multimeter, put one on a bolt on thecar, and then played with each wire and pressed the door switch, when the wire grounds then that is the wire that does the door switch i think...

Link to comment
https://www.sau.com.au/forums/topic/112847-neons/#findComment-2081423
Share on other sites

Hmm, has been a while since i did it, so the colours may be wrong, umm i got a multimeter, put one on a bolt on thecar, and then played with each wire and pressed the door switch, when the wire grounds then that is the wire that does the door switch i think...

did you have three or two wires?

Link to comment
https://www.sau.com.au/forums/topic/112847-neons/#findComment-2081426
Share on other sites

did you have three or two wires?

will be two wires in the drivers door. thin red is the one you are after. drop the switch out and look at it from there. the wire runs up the front pillar on the drivers side.

Link to comment
https://www.sau.com.au/forums/topic/112847-neons/#findComment-2082033
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • No idea about the remote start part. If the V37 nav is anything like other Nissan JDM vehicles, you can't get the factory Japanese nav working in australia, a card from a different car almost certainly won't work, those cards are usually matched to the serial number of the DCU.  You could be possibly swap out the components from a AuDM Q50 to get it working, but if this is a new model (2021+) 400R, then you will lose the newer features like ACP/AA.  That said, if you have ACP/AA, just use google maps.. I assume a band expander would be required to get the local radio stations, but don't forget the Japanese FM band is narrower than ours, so you still might not be able to receive all Australian stations. I can't see any reason the tyre pressure sensors won't work here, there is the sensor unit inside the rim and the receiver nearby in the wheel well.  I have never had to change the batteries on my 2015 Q50, so I assume they last quite a while.  A straight battery change shouldn't need them to be re-registered as they are the same unit, that should only be required if you replace a sensor with a new one.   Word of warning, if you ever go into the 'secret' diagnostics mode on the main screen, DO NOT EVER do a 'reset' in this menu, it will erase all of your model specific data in the DCU and you will need a trip to a dealer to re-program it all, which would be particularly painful being an import.  This applies to the AuDM Q50 too.
    • There is a known issue with the mix door motor on the Q50 which causes these symptoms, not sure if it is common on the Y51 though.
    • That ring thing is interesting how it's holding everything together 
    • Hey guys. I have a 400R on its way to Australia from Japan currently and have a few questions I’m hoping others may be able to help with.   Wondering if anyone here has had any luck getting the Sat nav unit to work in Australia!? Assuming the Stereo is as simple as a band expanded and tv won’t work?  Seeing as they’re based off a Q50 which is Aus delivered is there any way to link that system to the nav? Nav modules and head unit are different part numbers and appear slightly different at the rear with plug ins etc. can I put my xtrail sd card into the rv37 and will that convert the maps or update to Australian? Has anyone got any advice here?     also has anyone fitted the factory remote start and Security system once it’s landed in Australia? I put an enquirey to Nissan Japan in via a third party, and they suggested it needs a Nissan Japan dealers device to setup and couldn’t guarantee if one here could do it or not. They can supply and I can physically fit it but to setup I would need a dealers device. Any information here would be appreciated also. I’ve seen one here with it fitted already prior to leaving Japan at a dealer/inporter, so clearly passes compliance and works when fitted Japan and doesn’t need changing here.      also, does the tyre inflation sensors work here? Does anything change with them when the vehicle arrives? Where are they actually situated? I’ve read they have batteries and they need to changing at times and seems like resetting involves the nav system?    any help here would be appreciated and any other aust specific information to help would be great. Looking forward to see what the current generation skyline is like and eager to see how many of the gadgets can be utilised here.  Thanks in advance 
    • Do need to take it with a pinch of salt. One of the adapter failures, they clearly had setup issues with the flywheel.  One of the slipping ones I spoke to and it was pretty clear the throwout was riding, rather than fix, just swapped to a new clutch.    These clutches are being put in anything from 5k offroad 4x4 beaters, GR yaris, 500hp commodores to 1200hp barra monsters. Bound to be some issues in some of them when they are not a simple bolt in affair due to the changes in height.    There is a lot going on in this picture and unless I did the job myself no way to tell what really happened. 
×
×
  • Create New...